HIKVISION DS-7204HI-S Series Скачать руководство пользователя страница 24

Страница: 24 / 88

4.6 Manual Record

Note: The user must have the corresponding right, DVR has HDD and HDD has
been formatted already.

Manual record

In preview mode, press [REC] key, in the pop-up login dialog, select the name

and input the correct password, you can enter the “Manual Record” interface.

In menu mode, press [REC] key to enter the “Manual Record” interface directly.

Fig. 4.8 Manual record interface

Description

Manual record interface has follows parts: channel number, channel status,

start/stop record, start all and stop all buttons.

Channel

: List the channel number DVR has.

Status

: Channel work status has 4 cases:

means idle. Green means the

channel is recording (including real time recording, alarm recording, motion detection
recording). Red means network transmission. Orange means both recording and
network transmission.

Start/Stop

: “



” means you can start corresponding channel recording. “×”

means you can stop recording.

Start All

: Press this button to start all channels recording.

Stop All

: Press this button to stop all channel recording.

Press [ESC] key to enter the preview mode. Press [MENU] key to enter main

menu. Press [PLAY] key to enter the playback menu. Press [PTZ] key to enter the
PTZ control mode.

Содержание DS-7204HI-S Series

























































































Результаты поиска

Содержание DS-7204HI-S Series

Отзывы:

Похожие инструкции для DS-7204HI-S Series

Бренды по названию

Популярные бренды

HIKVISION DS-7204HI-S Series, Руководство пользователя

Результаты поиска

Содержание DS-7204HI-S Series

Отзывы:

Похожие инструкции для DS-7204HI-S Series

Бренды по названию

Популярные бренды