HIKVISION DS-2DF6236-CX Скачать руководство пользователя страница 92

Страница: 92 / 117

User Manual of Explosion-proof Dome

Select the

Region No.

from the dropdown list.

Adjust the

ROI level

from 1 to 6. The higher the value, the better image quality in the red

frame.

Enter a

Region Name



ROI for Dynamic Region

Check

Enable Face Tracking

checkbox to enable face tracking, and the captured face picture

is set as region of interest. Adjust the

ROI level

from 1 to 6.

Check

Enable Target Tracking

checkbox to enable target tracking, and the target is set as

region of interest. Adjust the

ROI level

from 1 to 6.

Click

to save the settings.

6.2.4

Display Info. on Stream

Check the

Enable Dual-VCA

checkbox, and the information of the objects will be marked in the

video stream. Then, you can set rules on the connected rear-end device to detect the events
including line crossing, intrusion, etc.

6.3

Configuring Image Settings



On the event configuration page, click to show the PTZ control panel or click to hide it.



Click the direction buttons to control the pan/tilt movements.



Click the zoom/iris/focus buttons to realize lens control.



The functions vary depending on different camera models.

6.3.1

Configuring Display Settings

Purpose:

Configure the image adjustment, exposure settings, day/night switch, backlight settings, white
balance, image enhancement, video adjustment, and other parameters in display settings.



The parameters in

Display Settings

interface vary depending on different camera models.



You can double click the live view to enter full screen mode and double click it again to exit.

Steps:

Enter the Display Settings interface:

Configuration > Image> Display Settings

You can select the

Scene

in the dropdown list with different predefined image parameters.

Set the image parameters of the speed dome.

Содержание DS-2DF6236-CX






















































































































Результаты поиска

Содержание DS-2DF6236-CX

Отзывы:

HIKVISION DS-2DF6236-CX, Руководство пользователя, Страница: 92 / 117

Результаты поиска

Содержание DS-2DF6236-CX

Отзывы: