HIKOKI DH 45ME, Инструкция по эксплуатации

Страница: 4 / 52

4
English
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
○ Plastic case ................................................................ 1
○ Side handle ................................................................. 1
○ Stopper ...................................................................... 1
○ Hammer Grease A ..................................................... 1
Standard accessories are subject to change without notice.
APPLICATIONS
Rotation and hammering function
○ Drilling anchor holes
○ Drilling holes in concrete
Hammering only function
○ Crushing concrete, chipping, digging, and squaring
(by applying optional accessories)
SPECIFICATIONS
The speci fi cations of this machine are listed in the Table on
page 43.
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci fi cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action Figure Page
Inserting SDS-max tools 1 44
Removing SDS-max tools 2 44
Changing tool direction 3 44
Selecting the operating mode 4 44
Switching on and o ff 5 44
About the power lamp 6 45
Speed change 7 45
Install the stopper 8 45
Using tapershank adapter 9 46
Removing tapershank adapter 10 46
Mounting core bit 11 46
Mounting guide plate and center pin 12 46
Selecting accessories* – 47, 48
* For detailed information regarding each tool, contact a
HiKOKI authorized service center.
Warming up (Fig. 13)
The grease lubrication system in this unit may require
warming up in cold regions.
Position the end of the bit so makes contact with the
concrete, turn on the switch and perform the warming
up operation. Make sure that a hitting sound is produced
and then use the unit.
CAUTION
When the warming up operation is performed, hold the
side handle and the main body securely with both hands
to maintain a secure grip and be careful not to twist your
body by the jammed drill bit.
Using Continuous operation button
The Continuous operation button feature is only available
for “Hammering Mode ”. Pressing the Continuous
operation button will switch on a blue LED that indicates
the activation of the Continuous operation function which
will keep the tool running even after the trigger switch is
released. To cancel the function, press the Continuous
operation button again or push the trigger switch to the
ON position. ( Fig. 14 )
NOTE
Continuous operation will be deactivated when the switch
is pressed. During continuous operation, keep your hand
away from the switch and grip the lower part of the handle
to avoid any unintentional contact with the switch. ( Fig.15 )
ABOUT THE PROTECTION
FUNCTION
This tool has a built-in protection circuit for preventing
damage to the unit in the event of an abnormality. Depending
on the nature of the abnormality, the display lamp will fl ash
as shown in Table 1 and the unit will cease to operate. In
such cases, verify the problem indicated by the fl ashing and
take whatever steps are necessary to correct the problem.
NOTE
Repair may be required if the display lamp continues to
fl ash after taking all necessary steps to correct the problem.
If the problem persists, please arrange for repairs.
Table 1
Display
lamp
fl ashing
Cause Solution
Flash
or
(110 V,
120 V,
127 V
ONLY)
The tool’s
temperature
increase protection
function gradually
reduced the
rotation speed
as the internal
temperature of the
tool approached
the speci fi ed
temperature range
for automatic
shutdown.
(Power regulation
function)
* The power
regulation function
will not activate if
only one or two of
the display lamp
bars are lighting.
The tool will return to
normal power once the
temperature is lowered
by reducing its load.
Continued operation
may result in automatic
shutdown by the tool’s
temperature increase
protection function.
(See row below)
Flash
Internal temperature
has risen beyond
the unit’s speci fi ed
temperature.
(Temperature
increase protection
function)
Turn o ff the unit
and allow it to cool
down for about 15 to
30 minutes.
When the temperature
goes down, press the
rotation speed selector
switch to recover.
Flash
Excessive pressure
applied to the tool
has resulted in an
overload.
(Overload
protection function)
Press the rotation
speed selector switch
to recover. Try to avoid
tasks that will apply
excess pressure to
the unit.
0000Book̲DH45ME.indb 4 0000Book̲DH45ME.indb 4 2017/11/30 15:39:39 2017/11/30 15:39:39