HIKOKI AC 18DA, Инструкция по эксплуатации

Страница: 8 / 236

8
English
5) Battery tool use and care
a) Recharge only with the charger speci fi ed by the
manufacturer.
A charger that is suitable for one type of battery pack
may create a risk of fi re when used with another
battery pack.
b) Use power tools only with speci fi cally
designated battery packs.
Use of any other battery packs may create a risk of
injury and fi re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a fi re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
e) Do not use a battery pack or tool that is damaged
or modi fi ed.
Damaged or modi fi ed batteries may exhibit
unpredictable behaviour resulting in fi re, explosion
or risk of injury.
f) Do not expose a battery pack or tool to fi re or
excessive temperature.
Exposure to fi re or temperature above 130°C may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range speci fi ed in the instructions.
Charging improperly or at temperatures outside
the speci fi ed range may damage the battery and
increase the risk of fi re.
6) Service
a) Have your power tool serviced by a quali fi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed
by the manufacturer or authorized service providers.
PRECAUTION
Keep children and in fi rm persons away.
When not in use, tools should be stored out of reach of
children and in fi rm persons.
CORDLESS CAULKING GUN SAFETY
WARNINGS
1. During use, hold the tool body securely with both hands.
( Fig. 2 )
2. Do not put an unreasonable burden on the tool that
causes the motor to lock, such as attempting to use
hardened sealing material.
Remove hardened sealing material, as it may cause
malfunction.
3. Before use, refer also to the directions on the packaging
of the sealing material to ensure that you use it correctly.
4. Wear safety glasses while working.
5. Do not use in locations where in fl ammable materials
such as lacquer, paint, benzene, thinner or gasoline are
present.
6. If you notice that the unit is generating unusually high
temperatures, operating poorly, or making abnormal
noises, immediately stop using and shut o ff the power
switch. Request an inspection and repair from the dealer
where you purchased the unit or a HiKOKI Authorized
Service Center.
Continuing to use while operating abnormally might
cause injuries.
7. If the unit is mistakenly dropped or strikes another object,
make a thorough check of the unit for cracks, breakage
or deformation, etc.
Injuries might occur if the unit has cracks, breakage or
deformation.
8. Never touch moving parts.
Never place your hands, fi ngers or other body parts near
the tool’s moving parts.
9. NEVER leave tool running unattended. Turn power o ff .
Don’t leave tool until it comes to a complete stop.
10. When operating the tool in high locations, make sure
there is nobody below.
11. Never operate from an unstable footing, such as when
on a ladder or step ladder.
Doing so may cause an injury.
12. Do not strike the tool with other objects; avoid strong
impacts such as dropping the tool; and do not allow the
tool to get wet.
Any one of these can damage the built-in precision parts
and result in malfunction.
13. Do not expose directly your eye to the light by looking
into the light.
If your eye is continuously exposed to the light, your eye
will be hurt.
Wipe o ff any dirt or grime attached to the lens of the LED
light with a soft cloth, being careful not to scratch the
lens.
Scratches on the lens of the LED light can result in
decreased brightness.
14. Precautions during transport
• Release the switch on the body of the machine and
remove the battery.
• Carry the machine by the handle on its body.
• When transporting it via vehicle, take appropriate steps
to prevent it from falling over or being damaged.
ADDITIONAL SAFETY WARNINGS
1. Always charge the battery at a temperature of 0°C–40°C.
A temperature of less than 0°C will result in over charging
which is dangerous. The battery cannot be charged at a
temperature higher than 40°C.
The most suitable temperature for charging is that of
20°C–25°C.
2. Do not use the charger continuously.
When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
3. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
4. Never disassemble the rechargeable battery and
charger.
5. Never short-circuit the rechargeable battery.
Shortcircuiting the battery will cause a great electric
current and overheat. It results in burn or damage to the
battery.
6. Do not dispose of the battery in fi re. If the battery is burnt,
it may explode.
7. Bring the battery to the shop from which it was purchased
as soon as the post-charging battery life becomes too
short for practical use. Do not dispose of the exhausted
battery.
00Book̲AC18DA̲EU.indb 8 00Book̲AC18DA̲EU.indb 8 2022/03/07 10:15:19 2022/03/07 10:15:19