HIKOKI 68102617, Инструкция по эксплуатации, Страница: 4 / 128

4
English
○ When cutting metallic materials, use proper machine
oil (turbine oil, etc.). When not using liquid machine oil,
apply grease over the workpiece.
The service life of the saw blade will be drastically
shortened if you don’t use machine oil.
○ Never apply any unreasonable force to the saw blade
when cutting. Also remember to press the base against
the lumber fi rmly.
Sawing curved lines
○ We recommend that you use the BI-METAL blade
mentioned in Table 2 for the saw blade since it is tough
and hardly breaks.
○ Delay the feed speed when cutting the material into
small circular arcs. An unreasonably fast feed may break
the blade.
Plunge cutting (Fig. 9 and 10)
○ Avoid plunge cutting for metallic materials. This can
easily damage the blade.
○ Never pull the switch trigger while the tip of the saw
blade tip is pressed against the material. If you do so, the
blade can easily be damaged when it collides with the
material.
○ Make absolutely sure that you cut slowly while holding
the body fi rmly. If you apply any unreasonable force to
the saw blade during the cutting operation, the blade can
easily be damaged.
12. Cut o ff guide for cutting pipe (optional accessory)
Please refer to the cut o ff guide user’s manual for details
on how to use it correctly.
SYMBOLS
WARNING
The following show symbols used for the machine. Be
sure that you understand their meaning before use.
CR13V2: Reciprocating Saw
To reduce the risk of injury, user must read
instruction manual.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2012/19/
EU on waste electrical and electronic equipment
and its implementati on in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Switching ON
Switching OFF
Stroke
Disconnect mains plug from electrical outlet
Class
II
tool
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
○ Blade (No. 341) .............................................................1
○ Case .............................................................................1
○ Hexagonal bar wrench ..................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
○ Cutting pipe and angle steel.
○ Cutting various lumbers.
○ Cutting mild steel plates, aluminum plates, and copper
plates.
○ Cutting synthetic resins, such as phenol resin and vinyl
chloride.
For details refer to the section entitled “SELECTION OF
BLADES”.
SPECIFICATIONS
Voltage (by areas) *
(110 V, 115 V, 120 V, 127 V,
220 V, 230 V, 240 V)
Power Input 1010 W *
Capacity
Mild Steel Pipe O.D. 130 mm
Vinyl Chloride
Pipe
O.D. 130 mm
Wood Depth 300 mm
Mild Steel Plate Thickness 19 mm
No-Load Speed 0 – 2800 min –1
Stroke 29 mm
Weight (without cord)** 3.3 kg
* Be sure to check the nameplate on product as it is subject
to change by areas.
** According to EPTA-Procedure 01/2014
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci fi cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action Figure Page
Mounting the blade 1 116
Taking the broken blade out 2 116
Maintenance and inspection of
saw blade mount
3 116
Blade hole 4 116
Adjusting the base 5 117
Switch Operation 6 117
Selection of saw blade length 7 117
Fastening work piece fi rmly 8 117
Plunge cutting
9 118
Plunge cutting with the saw blade
installed in reverse
10 118
Replacing carbon brushes 11 118
Selecting accessories ― 119
Refer to Table 1, 2, 3 and 4 for use of the blades.
0000Book̲CR13V2.indb 4 0000Book̲CR13V2.indb 4 2019/03/08 9:19:39 2019/03/08 9:19:39