High-Flying HF-LPT220 Скачать руководство пользователя страница 38

Страница: 38 / 65

HF-LPT220 Low Power WiFi Module User Manual

Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)

- 38 -



Parameters:



len: Range 8 ~1000; Unit: Byte. Auto-frame trigger length;

4.2.2.18.

AT+UARTTE



Function: Set/Query UART free-frame trigger time between two bytes;



Format:



Query Operation

AT+UARTTE<CR>

+ok=<mode><CR><LF><CR><LF>



Set Operation

AT+UARTTE=<mode><CR>

+ok<CR><LF><CR><LF>



Parameters:



mode:



fast: No free-frame trigger time, the uart data may be break into two fragment



normal: free-frame trigger time between two bytes is 50ms;

4.2.2.19.

AT+SEND



Function:

Send Data to SOCKA at Command Mode



Format:

AT+SEND=<data_lenth><CR>

+ok<CR><LF><CR><LF>



Parameters:



data_lenth: Lenth of send data. Range: 0~1000 Byte

The UART port will wait 3 seconds for input after this command is sent OK. The data received

from UART port is sent to SOCKA. If the interval of two bytes is more than 10ms, the data will be

sent instantly.

4.2.2.20.

AT+RECV



Function:

Receive Data from SOCKA at Command Mode



Format:

AT+RECV=<data_lenth,timeout><CR>

+ok=< data_lenth, data_content><CR><LF><CR><LF>



Parameters:



data_lenth: Lenth of receive data. Range: 0~1000 Byte



timeout: wait for timeout, 0~10 sec



data_content: contents of receive data.

If not receive any data in 3 second, then feok=0.

4.2.2.21.

AT+PING



Function: Network “PING” Instruction.



Format:



Set Operation

AT+PING=<IP_address ><CR>

+ok=<sta><CR><LF><CR><LF>

Содержание HF-LPT220


































































Результаты поиска

Содержание HF-LPT220

Отзывы:

Похожие инструкции для HF-LPT220

Бренды по названию

Популярные бренды

High-Flying HF-LPT220, Руководство пользователя

Результаты поиска

Содержание HF-LPT220

Отзывы:

Похожие инструкции для HF-LPT220

Бренды по названию

Популярные бренды