High End Systems SolaFrame 3000 Скачать руководство пользователя страница 28

Страница: 28 / 32

SolaFrame 3000

Frost Wheel

This message displays after the reset of the fixture if any of the following conditions exist:

•

if the magnetic-indexing circuit malfunctions (optical or magnetic sensor failure)

•

if the stepper motor is defective or the related IC driver on the main PCB has failed

•

if the Frost movement is not located in the default position after the reset

Gobo Rot 1

This message displays after the reset of the fixture if any of the following conditions exist:

•

if the magnetic-indexing circuit malfunctions (optical or magnetic sensor failure)

•

if the stepper motor is defective or the related IC driver on the main PCB has failed

•

if Gobo Rotating Wheel 1 is not located in the default position after the reset

Gobo Wheel 1

This message displays after the reset of the fixture if any of the following conditions exist:

•

if the magnetic-indexing circuit malfunctions (optical or magnetic sensor failure)

•

if the stepper motor is defective or the related IC driver on the main PCB has failed

•

if Gobo Wheel 1 is not located in the default position after the reset

Gobo Wheel 2

This message displays after the reset of the fixture if any of the following conditions exist:

Pan movement

This message displays after the reset of the fixture if any of the following conditions exist:

•

if the yoke’s magnetic-indexing circuit malfunctions (optical or magnetic sensor failure)

•

if the stepper motor is defective or the related IC driver on the main PCB has failed

•

if the Pan movement is not located in the default position after the reset

Prism Wheel movement

This message displays after the reset of the fixture if any of the following conditions exist:

•

if the fixture head magnetic-indexing circuit malfunctions (optical or magnetic sensor
failure)

•

if the stepper motor is defective or the related IC driver on the main PCB has failed

•

if the Prism movement is not located in the default position after the reset

Prism_Rot Wheel movement

This message displays after the reset of the fixture if any of the following conditions exist:

•

if the fixture head magnetic-indexing circuit malfunctions (optical or magnetic sensor
failure)

•

if the stepper motor is defective or the related IC driver on the main PCB has failed

•

if the Prism_Rot movement is not located in the default position after the reset

Содержание SolaFrame 3000

































Результаты поиска

Содержание SolaFrame 3000

Отзывы:

Похожие инструкции для SolaFrame 3000

Бренды по названию

Популярные бренды

High End Systems SolaFrame 3000, Руководство пользователя

Результаты поиска

Содержание SolaFrame 3000

Отзывы:

Похожие инструкции для SolaFrame 3000

Бренды по названию

Популярные бренды