background image

8

Installation

Installation Notes

The amplifier is generally mounted in the rear trunk area but can be mounted in any convenient area such as beneath a seat. 

Please be sure to locate this unit where you have reasonable air circulation and protection from moisture. When considering the 

mounting location you should minimize the length of the power and speaker leads. Minimizing both leads will yield a more reliable 

installation. It is also important to ensure that the heat sink fins are not against a panel or a surface, preventing air circulation. Do 

not install the amplifier on a subwoofer box or on vibrating parts of the vehicle, since the vibrations can cause damage to the 

amplifiers electrical components.

Installation of the amplifier

Before starting with the installlation, mount the provided mounting brackets on the 

amplifier. Mark the location for the mounting screw holes by using the amplifier as a 

template. Drill holes at the marked locations as and firmly fasten the amplifier in place 

with the mounting screws supplied in the accessory kit. Before drilling or cutting any holes, 

investigate the layout of your automobile thoroughly: Take care when working near the 

gas lines or hydraulic lines and electrical wiring.

Electrical Connection

Ground (GND)

This wire is the electrical ground and must be fastened securely to the vehicle chassis. The best method is to use a threading 

sheet metal screw since the threads cut into bare metal. Ensure that all paint or other insulationis removed from around the hole 

area, and using self tapping screw, securely affix the bare wire ends to the vehicle chassis. Use as short a piece of cable as 

possible - use the same gauge as was used for the +12V cable. Make sure that the connection is safe and stable.

Remote (REM)

Connect the remote wire of your headunit with the remote turn-on of the power amplifier.

Battery Connection (+12V Power)

This wire is usually connected directly to the positive battery terminal. Ensure that the + power supply wire is fused via an in-line 

fuse near by the battery. Please use a sufficient gauge (min 16 mm) with spade lug with insulating sleeve.

Fuses

The integrated amplifier fuses protect the units from short circuit and overload. The fuse rating is for 4 Ohm loads (impedance) of 

the speakers, for 2/1 Ohm loads the fuses may have to get increased by up to 50%/100% in case of higher power consumption.

In-Line

Fuse

Remote Wire

 (REM)

Ground-Connection

to vehicle's chassis

Ground-

Connection

Battery

12 V

Содержание Brutus Series BXi 1100 D MkII













Отзывы: