Hifonics Brutus BRZ 1200.1D, Руководство пользователя

Страница: 7 / 14

INPUT OUTPUT INPUT LEVEL
PHASE REMOTE BASS EQ SONIC LOW P
ASS
L
L
R
R
SUB
IN
OUT
POWER PROTECT
OUTPUT MASTER
INPUT SLA
VE
BALANCED
9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz
BA
TT+12V GND
POWER INPUT
SPEAKER OUTPUT
REM - - + +
INPUT OUTPUT INPUT LEVEL
PHASE REMOTE BASS EQ SONIC LOW P
ASS
L
L
R
R
SUB
IN
OUT
POWER PROTECT
OUTPUT MASTER
INPUT SLA
VE
BALANCED
9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz
BA
TT+12V GND
POWER INPUT
SPEAKER OUTPUT
REM - - + +
INPUT OUTPUT INPUT LEVEL
PHASE REMOTE BASS EQ SONIC LOW P
ASS
L
L
R
R
SUB
IN
OUT
POWER PROTECT
OUTPUT MASTER
INPUT SLA
VE
BALANCED
9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz
BA
TT+12V GND
POWER INPUT
SPEAKER OUTPUT
REM - - + +
DUAL AMP INSTALLATION PROCEDURE: 4. Route two 0 gauge power cables directly to the vehicle battery with an in-line fuse.
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out 5. Connect two 0 gauge ground cables directly to the chassis with in 36” of the amp.
puts with good quality RCA interconnect cables. - Be sure to remove any paint or primer from the ground point.
2. Plug in the HFR-3 bass remote module into the amp REMOTE INPUT jack on the - Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
Master amp. This will allow the Master amp to control both Master and Slave amps 6. Make sure the Master amp MASTER/SLAVE switch is in the MASTER position.
with just one Bass Remote. Make sure the Slave amp MASTER/SLAVE switch is in the SLAVE position.
3. Connect an RCA jumper cable from the Master amp MASTER OUTPUT to the 7. Connect the subwoofer(s) in accordance to the diagrams below.
Slave amp SLAVE INPUT. Note: This will “link” the amps so that the Master amp 8. Connect a 12 gauge jumper from Master amp speaker - to Slave amp speaker - as
crossover switches will control both the Master and Slave amps. The Slave amp
shown below.
crossover switches will be bypassed.
SINGLE AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
puts with good quality RCA interconnect cables.
2. Plug in the HFR-3 remote module into the amp REMOTE INPUT jack.
3. Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse.
4. Connect a 0 gauge ground cables directly to chassis ground with in 36” of the amp.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
5. Connect the subwoofer(s) in accordance to the diagrams below.
6. Make sure the MASTER/SLAVE switch is in the MASTER position.
Note: The amplifier will not work if the MASTER/SLAVE switch is in the Slave position
FULL RANGE
STEREO LINE INPUT
NOT USED
Y-ADAPTOR
Note: You can use the Radio/CD designated mono line output
or a full range stereo line output. For full range stereo line
output, you will need an optional “Y-Adaptor” as shown.
BRZ2100.1D / BRZ2400.1D MONO AMPLIFIER APPLICATIONS
Basic application
HFR - 3
MI N MAXX
BOOST
+12V GND
POWER SPEAKER
REM
+
-
+
-
MONO
SUBWOOFER
REMOTE TURN-ON
CHASSIS GROUND
TO B 12 Volts
VIA FUSE
PARALLEL MONO
SUBWOOFERS
2 OHMS EACH MINIMUM
Linking two amps for single or dual subwoofer application
Amplifiers are stable to 2-Ohms linked
5
HFR - 3
MI N MAXX
BOOST
12 GAUGE JUMPER WIRE
RCA
JUMPER CABLE
MASTER OUTPUT T
O SLA
VE INPUT
DESIGNATED
MONO OUTPUT
FROM HEAD UNIT
DESIGNATED
MONO OUTPUT
FROM HEAD UNIT
Master remote controls
both amplifiers when
LINKED
OUTPUT
MASTER
INPUT
SLAVE
IN
OUT
OUTPUT
MASTER
INPUT
SLAVE
IN
OUT
(MASTER)
(SLAVE)