background image

 

VertX V1000 (CS) Quick Installation Guide 

 

 

 

 

 

I n t r o d u c t i o n

 

VertX™ CS is the first family of access controllers designed specifically for alarm dealers for direct 
connection to central stations. Because it was designed with the central station in mind, VertX CS works 
with software from leading central station automation providers, including Bold Technologies, DICE, Micro 
Key, and Patriot Systems. 
 
The V1000 is designed to control readers, door contact inputs and relays through the RS-485 loop and any 
combination of up to 32 Interface Panels (V100 Door/Reader Interface, V200 Input Monitor Interface and/or 
V300 Output Control Interface). In addition, the V1000 Access Controller manages communications with the 
central station automated software. 

P a r t s   L i s t  

Description 

Quantity 

VertX™ V1000 Access Controller 

Note:

 The V1000 controller has a plastic base and is covered with a Plastic or Mylar cover. 

- Lithium Battery 

- Mounting screws 

- 2.2K EOL resistors 

- HID Serial Adapter cable (P/N 70007) 

- Quick Installation Guide 

- Installation Wiring Diagram Example 

Note:

 One or more VertX Interface panels are required.  

Note:

 A modem and RS-232 Serial cable must be purchased separately if your installation includes a modem. 

P r o d u c t   S p e c i f i c a t i o n s  

Description  

Specification 

Power Supply  

12-16VDC 

Maximum current at 12VDC per V1000 

1 Amp 

Average operating current at 12VDC 

210mA 

Operating temperature range  

32°-122°F  (0°-50°C)      

Humidity  

5% to 95% non-condensing 

Ca b l e   S p e c i f i c a t i o n s  

Cable Type 

Length 

Specification 

Use Belden 3105A, 22AWG twisted pair, shielded 100

Ω

 cable, or 

equivalent. 

RS-485 * 

4000 feet (1220 m) to host 

Use any RS232 Serial modem cable specified by the modem 
manufacturer. 

15 feet (4.57 m) for RS232 Serial 
modem cable  

RS-232 

HID Serial Adapter cable, P/N 70007. 

6 inch (15.24 cm) adapter 

2-conductor, shielded, using ALPHA 1292C (22AWG) or Alpha 2421C 
(18AWG), or equivalent.  

Input Circuits * 

500 feet (150 m) 

2-conductor, using ALPHA 1172C (22AWG) or Alpha 1897C (18AWG), 
or equivalent. 

Output Circuits * 

500 feet (150 m) 

October 2006 

 

 

Page 3 of 20 

© 2006 HID Global Corporation.  All rights reserved.

 

Содержание VertX V1000























Отзывы: