background image

www.hi-velocity.com

© 1995-2020 Energy Saving Products Ltd.

© 1995-2020 Energy Saving Products Ltd.

Module RPM-E

Refrigerant Module Installation

-7-

-7-

•  Inoperative parts must be returned to Energy Saving Products Ltd. with an ESP RMA Form that 

includes model, serial number, and a detailed description of the entire problem. Inoperative parts 

must be returned in testable condition.

•  This warranty does not cover shipping costs to and from the factory, labor costs or any other cost 

associated with the installation of the replacement part.

•  Energy Saving Products Ltd. is not liable for any other damages, personal injury, or any other losses 

of any nature.

•  The liability of Energy Saving Products Ltd. is limited to and shall not exceed the cost of pre-approved 

replacement parts.

WARRANTY

A

 

Three (3) Year Limited Warranty

 

is extended on Electric Strip Heaters

.

Five (5) Year Limited Warranty

 

is extended on all components in products manufactured exclusively 

by Energy Saving Products. These components include Motors, WEG Controller, Circuit Boards, Dampers, 
Zoning Controls, Blowers, Motor & Blower Assemblies, Heating Coils, Chilled Water Coils, and Air 
Conditioning Coils.  Note:  If any product is installed in or exposed to a corrosive environment, warranty 
will be void.

 

   

 Energy Saving Products Ltd. is proud to offer a limited warranty. This warranty applies strictly to the first 

purchaser at wholesale level and only to the fan coil unit and module. It does not include connections, attachments 

and other products or materials furnished by the installer.

TERMS & CONDITIONS

•  Any repair performed under warranty must be approved by Energy Saving Products Ltd. for this 

warranty to be valid.

This warranty replaces all other warranties expressed or implied.  

 

www.hi-velocity.com

•  Should there be multiple consecutive failures of a single part, warranty will not be considered unless 

a contractor has contacted Energy Saving Products Ltd. Technical Department for assistance, and 

received a tech code. 

Follow these steps for Service or Repair:

1. 

Contact the installer of the product or a licensed service company                                                                   

2. 

Contact the distributor    

 

 

 

 

 

 

                                        

3. 

Contact Energy Saving Products Ltd.  Mon-Fri  8 am – 4:30 pm MT  1-888-652-2219

     

This warranty excludes any damages caused by changes, relocation to, or installation in a new site. This warranty 

does not cover any defects caused by failure to follow the installation and operating instructions furnished with 

the fan coil. This warranty does not cover defects caused by failing to adhere to local building codes and following 

good industry standards. Failure to correctly install the fan coil, or material related to the unit, may result in 

improper system performance and/or damages and will void this warranty. This warranty does not cover material 

installed in or exposed to a corrosive environment. This warranty does not cover products subjected to abnormal 

use, misuse, improper maintenance, or alteration of the product. Using the fan coil and/or module as a source of 

temporary heating/cooling during construction will void this warranty. 

Products sold by Energy Saving Products but manufactured by others, will carry the original 
manufacturer’s warranty. 

Содержание RPM-E









Отзывы: