Hi-Target V90 Plus Скачать руководство пользователя страница 6

Страница: 6 / 128

V90 Plus GNSS RTK System Getting Started

1. Products Introductions

1.1 Preface

Small and lightweight

◇

Only weighs 950g.

◇

Measures Diameter 153mm x Height 83mm.

Multi-constellation Tracking

◇

220 tracking channels

◇

Supports GPS, GLONASS, GALILEO, BDS, SBAS

◇

NGS approved full-band GNSS antenna

1.2 Product characteristics

V90 Plus is a new type of GNSS receiver used for measurement pushed forward by Hi-Target

recently. With a hi-tech, fully integrated design, the conveniently sized V90 Plus is one of the most

flexible choices for any measuring task. Built-in Linux3.2.0 operating system, pre-loaded multiple

smart applications such as tilt surveying, electronic bubble calibration, NFC and voice DIY, LEDs

enable you to monitor satellite tracking, radio reception, data logging status, Wi-Fi status, and

power. Bluetooth wireless technology provides cable-free communications between the receiver and

controller.V90 Plus GNSS system provides surveyor industry-leading GNSS solutions.

Warning:

the instruction represents no standard configuration. The articles within the box can be adjusted

according to different user requirements. The specific configuration shall be subject to the outgoing

list upon purchasing. The suggestions before using the machine: check whether the product package

is damaged; please open the package carefully and confirm whether the articles are consistent with

outgoing list; in case of loss or damage in the product and its accessories, please immediately contact

with local office or dealers; please carefully read the operating instruction before carrying,

transporting and using the product.

Содержание V90 Plus
































































































































Результаты поиска

Содержание V90 Plus

Отзывы:

Бренды по названию

Популярные бренды

Hi-Target V90 Plus, Начало работы

Результаты поиска

Содержание V90 Plus

Отзывы:

Бренды по названию

Популярные бренды