Hettich Marketing- und Vertriebs GmbH & Co. KG · Vahrenkampstraße 12 -16 · 32278 Kirchlengern · Téléphone + 49 52 23/77-0 · www.hettich.com
Hettich Marketing- und Vertriebs GmbH & Co. KG · Gerhard-Lüking-Straße 10 · 32602 Vlotho · T49 5733 798-0 · www.hettich.com
Hettich Marketing- und Vertriebs GmbH & Co. KG · Gerhard-Lüking-Straße 10 · 32602 Vlotho · T49 5733 798-0 · www.hettich.com
Technik für Möbel
7
5
6
7
Changing desk height unit (cm or inch)
Besides plug detection, the control unit can also automatically detect the
number of lifting columns plugged in. This feature is always active during
first startup of the control unit and after returning the control unit to
factory settings (see section 9).
Lifting columns plugged in after the first startup of the control unit will
not be detected automatically. For changing the established configuration
the control unit has to be returned to factory settings.
Possible situations:
8
The control unit is being used for the first time.
8
The control unit has been returned to factory settings.
This function lets you change the memory handset display from centimetre
to inch and vice versa. This function does not alter desk height.
Handset display shows error code
.
E70
1. Unplug the control unit's power supply and wait at least 5
seconds.
3. Plug the control unit's power supply back in again.
4. Carry out a manual reset
2
2
2
1
1
1
Simultaneously press
,
memory position button 1 memory
position button 2
desk top up button
and the
.
Keep this button combination pressed for approx.
3 seconds.
The display shows
.
S 1
Now release the buttons.
Keep pressing the
until the display
desk top up button
shows
.
S 5
The display shows
.
S 5
Press the
.
save button
If the display was previously set to cm, it will now be
changed to inch. If the display was previously set to inch,
it will now be changed to cm.
9
Returning control unit to factory settings (S0 menu)
This function allows you to return the control unit to factory settings.
To be able to use the control unit again after changing a lifting column's
configuration in this way, proceed as follows:
2
2
2
1
1
1
Simultaneously press
,
memory position button 1 memory
position button 2
desk top up button
and the
.
Keep this button combination pressed for approx.
3 seconds.
The display shows
.
S 1
Now release the buttons.
Keep pressing the
until the display
desk top up button
shows
.
S 0
The display shows
.
S 0
Press the
.
save button
The control unit is returned to factory settings. The control
unit is now in the same state as it was when you put it
into operation for the first time.
8
Manual reset
Auto Detect Number of Drives
1.
2.
3.
If the actual desk top position no longer matches the desk top position displayed
or if a previously configured control unit is used at another electrically height
adjustable workstation of identical design, you must calibrate the end position
at the bottom most desk top position.
Warning!
is
Collision detection (ISP) not active
in any reset cycle or during end position
calibration. Please realise that you could
get crushed!
Press the
.
desk top down button
Keep the
pressed until the desk top has
desk top down button
reached the lowest position (programmed end position).
Press the
again and continue to keep it
desk top down button
pressed. After approx. 5 seconds the desk top will continue
to move down until the bottom most desk top position is reached.
Release the
. The electrically height
desk top down button
adjustable workstation can be used in the normal way again.
8
(see )
SAVE
SAVE
Changing the height displayed for the lifting column position
This function is used to individually adjust the height shown on the manual
switch display to the actual height of the LegaDrive Systems lifting column
system.
Follow the steps described below to make this adjustment:
“
“ is shown on the display.
S –
Press the
for approx. 5 seconds.
desk top down button
The display indicator starts to flash.
Then use the
or
desk top down button
desk top down
button
to set the height indicator.
Press the
.
SAVE key
The height indicator is now set to the height position
entered.
Press the
.
SAVE key
SAVE
SAVE
SAVE
SAVE
Note
Please note that this adjustment does not modify the actual
position of the LegaMove lifting column system. This function
is only used to change the value shown on the display.
This function is only available for manual switches with
integrated display.
