background image

9

DK ASSIGNMENTS

Check the following list before turning on power to the 
receiver.

1. Be sure the motion toggle switches are in their 

Off (neutral) positions.

2. Be sure there are fully charged batteries in the 

transmitter. Refer to "Changing the Battery" on 
page 13.

HOLDING THE TRANSMITTER

Hold the transmitter with the control panel facing you. 
Be sure that you are able to easily read any text and 
understand operation symbols.

DK1

S1

DK2

DK7

DK8

S4

S5

DK9

DK10

DK5

DK6

S3

S2

DK3

DK4

S 0

S

to

p

HH-M-MFSHL TS5

S

to

p

DK1

DK2

DK3

DK4

DK5

DK6

DK7

DK8

DK10

S1

S2

S3

S4

S5

S6

DK11

DK12

HH-M-MFSHL TS6P

DK9

S 0

S

to

p

S

to

p

DK1

DK2

DK3

DK4

DK5

DK6

DK7

DK8

DK9

DK10

DK11

DK12

DK13

DK14

S1

S2

S3

S4

S5

S6

S7

HH-L-MFSHL TS7P

S

to

p

S

to

p

S 0

TEST PROCEDURES

WARNING: 

FAILURE TO FOLLOW 

INSTRUCTIONS could result in personal 
injury and/or damage to equipment. Read and 
understand the safety instructions in all 
manuals provided.

Testing or service must be performed by 
authorized personnel only.

There must be no load on the crane/machine.

Clear the crane/machine operating area of 
obstructions.

WARNING: 

FAILURE TO FOLLOW 

INSTRUCTIONS could result in personal 
injury and/or damage to equipment. Always 
hold the transmitter in the proper orientation. 
Holding the transmitter improperly while 
operating the crane/machine could result in 
unexpected crane/machine response.

PRELIMINAR

Y COPY

Содержание HH-L-MFSHL TS7P




















Отзывы: