HERKULES 43.014.42, Руководство по эксплуатации

Страница: 11 / 100

11
1. Layout (Fig. 1/2)
1. Feet
2. Diamond
wheel
3. Trough
4. Work
table
5. Angle stop
6. Rail fence
7. Chain bar
8. Safety hood for the cutting wheel
9. Handle
10. Star grip screw for setting the angle
11. Star grip screw for securing during transportation
12. Thumb screws
13. Cooling water pump
14. Hose
15. Motor
16. ON/OFF switch
17. Angle scale
2. Items supplied
앬 Stone cutting machine
앬 Trough (3)
앬 Cooling water pump (13)
앬 Angle stop (5)
앬 Feet (1)
3. Proper use
The stone cutting machine can be used for normal
cutting work on concrete slabs, cobblestones, marble
and granite slabs, bricks, tiles, etc. as long as the
machine is large enough to take them. It is designed
for DIY applications and craft businesses. It should
never be used for cutting wood or metal.
The
machine should be used exclusively for its
intended purpose.
No other use is permitted and
the manufacturer will not accept liability for any
damages or injury resulting from any such use;
responsibility rests with the user/operator in any such
case. Only use cutting wheels which are suitable for
the machine. Saw blades should never be used.
Compliance with the safety instructions, the
assembly instructions, and advice and instructions
on operation contained in the operating instructions
also falls under the terms of intended use. All
persons operating or carrying out maintenance work
on the machine must be acquainted with the above
and be aware of all potential dangers.
In addition, strict compliance with the accident
prevention regulations in force in your area, as well
as all other general rules of health and safety at
work, is imperative. The manufacturerʼs liability shall
be deemed void if the machine is modified in any
way and the manufacturer shall therefore accept no
liability for any damages arising as a result of
modifications. Even if the machine is used as
intended, certain residual risk factors cannot be
completely eliminated. For reasons of design and the
construction of the machine, the following
eventualities are possible:
앬
Contact with the diamond cutting wheel where it
is not covered.
앬 Contact with the diamond cutting wheel while it is
turning.
앬 Defective diamond tips flying off the cutting
wheel.
앬 Workpieces or parts of workpieces kicking back.
앬 Damage to hearing if the ear-muffs specified are
not used.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Important instructions
4.1. General
Please read this manual carefully and pay particular
attention to the instructions contained within it. Use
this information to get to know the machine, its
correct operation and safety regulations (see
supplementary sheet) before using for the first time.
4.2. Additional safety instructions
앬 Set up the machine on a level, non-slip floor.
Make sure that the machine does not wobble.
앬 Check that the voltage on the rating plate is the
same as your supply voltage. Only then are you
to insert the power plug in the socket-outlet.
앬 Wear safety goggles.
앬 Wear ear-muffs.
앬 Wear safety gloves.
앬 Never use cracked diamond cutting wheels.
Replace immediately.
앬 Never use segmented cutting wheels.
앬 Caution! The cutting wheel runs on after the
machine is switched off!
앬 Never apply side pressure to the diamond cutting
wheel in order to bring it to a halt.
앬 Caution! The diamond cutting wheel must be
cooled with water at all times.
앬 Always pull out the power plug before changing
the cutting wheel.
앬 Use only suitable diamond cutting wheels.
GB
Anleitung STR 250 LED_SPK7:Anleitung STR 250-1L_SPK1 07.12.2006 13:49 Uhr Seite 11