manualshive.com logo in svg

Hercules Hercules 1.5 HP, 175 RPM, Инструкция по безопасности, эксплуатации и техническому обслуживанию с перечнем запасных частей, Страница: 5 / 6

Поделиться
Скачать
Hercules Hercules 1.5 HP, 175 RPM Скачать руководство пользователя страница 5

(8) Super Heavy-Duty Floor Machine

 Super Heavy-Duty Floor Machine (5)

5.0   Operating Tips

•  For indoor use only. Sweep abrasive soils before 

scrubbing.

•  While the brush or pad driver is spinning, keep the floor 

machine moving to avoid “donut” burns on the floor.

To Start Operation:
•  Unlock the handle by raising the locking lever.
•  Lower the handle to a comfortable position, typically 

waist height.

•  Re-lock the handle by pushing the lever down. NEVER 

OPERATE THE MACHINE WITH THE HANDLE 

UNLOCKED.

•  This floor machine is a high torque motor. Hold the 

machine firmly with both hands when starting up.

•  Push the red safety interlock switch forward to unlock the 

dual triggers.

•  Squeeze the dual triggers to release power to the motor. 

Once power is on, either trigger will keep power to the 

motor.

•  To stop the floor machine release both triggers.
•  The spinning brush helps move the floor machine. (Lift 

the handle slightly to work to the right. Push the handle 

down slightly to work to the left.)

5.1   To Store your Machine

•  Lock the handle in the “up” position. Tilt the machine 

back and remove the pad driver or brush.

•  Wind the cord around the handles and the bottom cord 

hook.

•  Wash brushes or pads and hang to dry. Never store 

machine standing on the brush.

•  Inspect and maintain equipment on a regular schedule for 

best results.

•  Check and clean pads after each operation. Remove soil 

and chemical buildup. Replace worn or damaged pads.

•  Check the triggers and switches for proper operation.
•  Repair or replace damaged skirts and dumpers.
•  Use air pressure or vacuum to remove dust and debris 

from the motor vents.

•  Report problems and repair promptly.

2.1   Attach the Power Cord

The triple-wire grounded power cord has been factory-

installed into the handle tube. A flexible rubber cable 

connector (11) is used to secure the plug-in connections. 

The floor machine ships with this connector mounted 

on the cord coming out of the handle (10). Stretch the 

connector and slip the male connector (9) (coming out of 

the motor housing) through the connector hole and then 

into the female connector.
Now, plug the end of the 50-foot cord into a grounded 

power outlet. Squeeze the triggers on the handle and check 

for power to the motor.

2.2   Install a Brush or Pad Driver

A brush or pad driver mounts onto your floor machine with 

a “B” style Universal clutch plate.

Unplug the floor machine. Lock the machine handle in 

the “up” position and tip the floor machine back onto the 

handle.

Slide the brush or pad driver clutch plate (12) over the 

drive plug (13).

Give the brush a quick counter-clockwise spin to lock the 

brush onto the drive plug.

Now, lower the machine back onto the brush.

You’re ready to go to work.

Содержание Hercules 1.5 HP, 175 RPM







Отзывы:

Нет отзывов