Page 4
For technical questions, please call 1-888-866-5797.
Item 56459
11.
Position the cord clear of the spinning
accessory.
If you lose control, the cord may be cut or
snagged and your hand or arm may be
pulled into the spinning accessory.
12.
Never lay the power tool down until the
accessory has come to a complete stop.
7KHVSLQQLQJDFFHVVRU\PD\JUDEWKHVXUIDFH
DQGSXOOWKHSRZHUWRRORXWRI\RXUFRQWURO
13.
Do not run the power tool while carrying
it at your side.
Accidental contact with the
VSLQQLQJDFFHVVRU\FRXOGVQDJ\RXUFORWKLQJ
SXOOLQJWKHDFFHVVRU\LQWR\RXUERG\
14.
Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside
WKHKRXVLQJDQGH[FHVVLYHDFFXPXODWLRQRI
SRZGHUHGPHWDOPD\FDXVHHOHFWULFDOKD]DUGV
15.
Do not operate the power tool near flammable
materials.
6SDUNVFRXOGLJQLWHWKHVHPDWHULDOV
16.
Do not use accessories that require liquid
coolants.
Using water or other liquid coolants
may result in electrocution or shock.
17. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
18. Avoid unintentional starting. Prepare to
begin work before turning on the tool.
19. Do not depress the spindle lock when
starting or during operation.
20. Do not leave the tool unattended when it is plugged
into an electrical outlet. Turn off the tool, and
unplug it from its electrical outlet before leaving.
21. Use clamps (not included) or other practical
ways to secure and support the workpiece to
a stable platform. Holding the work by hand
or against your body is unstable and may
lead to loss of control and personal injury.
22. This product is not a toy.
Keep it out of reach of children.
23. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
In addition, people with pacemakers should:
• Avoid operating alone.
• Do not use with Switch locked on.
• Properly maintain and inspect to avoid
electrical shock.
• Properly ground power cord. Ground Fault Circuit
Interrupter (GFCI) should also be implemented
– it prevents sustained electrical shock.
24. The warnings, precautions, and instructions
discussed in this instruction manual cannot cover all
possible conditions and situations that may occur.
It must be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush
or any other accessory. Pinching or snagging
causes rapid stalling of the rotating accessory
which in turn causes the uncontrolled power
tool to be forced in the direction opposite of the
accessory’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward
or away from the operator, depending on direction
of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.
1.
Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.
7KHRSHUDWRUFDQFRQWUROWRUTXHUHDFWLRQVRU
NLFNEDFNIRUFHVLISURSHUSUHFDXWLRQVDUHWDNHQ
2.
Never place your hand near the rotating
accessory.
Accessory may kickback over your hand.
3.
Do not position your body in the area where
power tool will move if kickback occurs.
.LFNEDFNZLOOSURSHOWKHWRROLQGLUHFWLRQRSSRVLWHWR
WKHZKHHO¶VPRYHPHQWDWWKHSRLQWRIVQDJJLQJ
4.
Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory.
&RUQHUVVKDUSHGJHVRUERXQFLQJ
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
5.
Do not attach a saw chain woodcarving
blade or toothed saw blade.
Such blades
create frequent kickback and loss of control.
Safety Warnings Specific
for Grinding and Abrasive
Cutting-off Operations
1.
Use only wheel types that are recommended
for your power tool and the specific
guard designed for the selected wheel.
:KHHOVIRUZKLFKWKHSRZHUWRROZDVQRWGHVLJQHG
cannot be adequately guarded and are unsafe.
