Page 3
For technical questions, please call 1-888-866-5797.
Item 57348
Power Tool Use and Care
1.
Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
2.
Do not use the power tool if the Trigger
does not turn it on and off.
Any power tool
that cannot be controlled with the Trigger
is dangerous and must be repaired.
3.
Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
4.
Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool.
Power tools are
dangerous in the hands of untrained users.
5.
Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use.
Many accidents
are caused by poorly maintained power tools.
6.
Keep cutting tools sharp and clean.
Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7.
Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the
power tool is maintained.
Safety Warnings Common for
Grinding, Sanding, Wire Brushing,
or Abrasive Cutting-off Operations
1.
This power tool is intended to function as a
grinder, sander, wire brush, or cut-off tool. Read
all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
2.
Operations such as polishing are not
recommended to be performed with
this power tool.
Operations for which the
power tool was not designed may create
a hazard and cause personal injury.
3.
Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer.
Just because the
accessory can be attached to your power tool,
it does not assure safe operation.
4.
The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool.
Accessories running faster than
their RATED SPEED can break and fly apart.
5.
The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool.
Incorrectly sized accessories
cannot be adequately guarded or controlled.
6.
The arbor size of wheels, flanges, backing
pads or any other accessory must properly
fit the spindle of the power tool.
Accessories
with arbor holes that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
7.
Do not use a damaged accessory.
Before each use inspect the accessory such
as abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess wear,
wire brush for loose or cracked wires. If power
tool or accessory is dropped, inspect for
damage or install an undamaged accessory.
After inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run
the power tool at maximum no-load speed
for one minute.
Damaged accessories will
normally break apart during this test time.
8.
Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and workshop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must
be capable of stopping flying debris generated
by various operations.
The eye protection must
be capable of stopping flying debris generated by
various operations. The dust mask or respirator
must be capable of filtering out particles generated
by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
9.
Keep bystanders a safe distance away
from work area. Anyone entering the
work area must wear personal protective
equipment.
Fragments of workpiece or of a
broken accessory may fly away and cause
injury beyond immediate area of operation.
10.
Hold power tool by insulated gripping surfaces
only, when performing an operation where
the accessory may contact hidden wiring
or its own cord.
An accessory contacting a
″live″ wire may make exposed metal parts of
the power tool ″live″ and shock the operator.
