Heras HGD230 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 146

background image

EN – Translation of the original user manual - 2.1 | 2019

20

3.2.4

Disengaging the motor

The gate can be opened by hand in emergency situations. The gear wheel of the
drive unit will have to be disengaged from the toothed bar for this.

•

Open the drive unit cabinet (key)

•

Set the automatic fuse to “OFF”.

•

Pull the disengagement lever forwards after
which the gate can be opened and closed

manually.

Illustration 8:

release the motor

3.2.5

Engaging the motor

•

When locking the system again, close the gate

as far as the mark on the bottom rail. Now move

the gate back and forward a bit to engage the

gear wheel with the rack.

•

Set the automatic fuse to “ON”. Lock the drive

unit cabinet after use.

Illustration 9:

lock the motor

NOTE: ONLY engage the gate when it is in the CORRECT POSITION.
Only then will the software recognise the correct end positions.
Engaging the gate in the wrong position will lead to damage and the
gate will operate incorrectly.
See Menu 7.3 end positions and section 7.3.1 Marking plate for
more information.

«
...
18
19
20
21
22
...
»

Содержание HGD230



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HGD230

Бренд: quiko Страницы: 32

Smart Phone Control

Бренд: Automatic Technology Страницы: 4

Бренд: FAAC Страницы: 49

Бренд: Novoferm Страницы: 46

Бренд: Black & Decker Страницы: 8

Gizmo EM200 Series

Бренд: Black & Decker Страницы: 2

Keystone Series

Бренд: Max Страницы: 4

Бренд: HySecurity Страницы: 69

Бренд: Upswung Страницы: 50

Бренд: Jaytech Страницы: 21

Бренд: Bauer Страницы: 39

Бренд: Alutech Страницы: 40

Бренд: Chamberlain Страницы: 16

Бренд: Chamberlain Страницы: 44

Бренд: TMT Automation Страницы: 16

Бренд: TOPP Страницы: 60

Бренд: TOPP Страницы: 56

Бренд: Accessmatic Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды