Henny Penny 581 Скачать руководство пользователя страница 8

Страница: 8 / 12

Henny Penny

Model 581

Problem

Cause

Correction

LID/PRESSURE SECTION (Continued)

• Safety relief valve leaking.

• Check and replace if
necessary per maintenance
section on the relief valve.

• Pressure pad broken or crushed.

• Replace pressure pads.

Lid won’t move

• Cable on Counterweight

• Put cable on Counterweight

up or down

loose or broken

per section on

Counterweight Cable.

• Check operation of

• Make proper adjustments.

counterweight carriage in
rear of cooker.

HEATING OF SHORTENING SECTION

Shortening will

• Blown fuse or tripped

• Reset breaker or replace

not heat

circuit breaker at supply

fuse.

box or control panel.

• Blown fuse at control panel.

• Check fuse per Main-
tenance Section on fuses

• Faulty Cook/Pump switch.

• Check Cook/Pump switch
per Maintenance Section on
Cook/Pump switch.

• Faulty Cord and Plug.

• Check cord and plug and
power at wall receptacle.

• Faulty contactor.

• Check contactor per
Maintenance Section on
contactors.

• Faulty Drain Switch.

• Check drain switch per
Maintenance Section on
Drain Switches.

• Faulty PC board.

• Remove and replace control
panel.

• Faulty high limit control

• Check high limit control

switch.

switch per Maintenance
Section on High Limits.

4-8

1201

Содержание 581













Результаты поиска

Содержание 581

Отзывы:

Похожие инструкции для 581

Бренды по названию

Популярные бренды

Henny Penny 581, Руководство по устранению неисправностей

Результаты поиска

Содержание 581

Отзывы:

Похожие инструкции для 581

Бренды по названию

Популярные бренды