background image

Definitions of Hazard Levels

Identify the hazard levels used in this manual
with the following definitions and signal words:

DANGER

Watch for this symbol:

It Means:

Immediate hazards which will result

in severe personal injury or death.

WARNING

Watch for this symbol:

It Means:

Hazards or unsafe practices which

could result in severe personal injury or death.

CAUTION

Watch for this symbol:

It Means:

Hazards or unsafe practices which

could result in minor personal injury or product
or property damage.

Watch for this symbol! It means 

BE ALERT!

Your safety, or the safety of others, is

involved!

Owner's Responsibility

To maintain machine and user

safety, the responsibility of the owner is to
read and follow these instructions:

• Follow all installation instructions.

• Make sure installation conforms to all

applicable Local, State, and Federal
Codes, Rules, and Regulations; such as
State and Federal OSHA Regulations
and Electrical Codes.

• Carefully check the unit for correct

initial function.

• Read and follow the safety instructions.

Keep them readily available for
machine operators.

• Make certain all operators are properly

trained, know how to safely and
correctly operate the unit, and are
properly supervised.

• Allow unit operation only with all parts

in place and operating safely.

• Carefully inspect the unit on a regular

basis and perform all maintenance as
required.

• Service and maintain the unit only with

authorized or approved replacement
parts.

• Keep all instructions permanently with

the unit and all decals on the unit clean
and visible.

COATS 4050A Tire Changer • 1

DANGER

DANGER

Explosion Hazard

Never exceed 40
PSI while seating
beads.

Explosion Hazard

Never inflate
tire above
manufacturer's
recommended
pressure after bead
is seated.

CAUTION

!

WARNING

!

DANGER

!

Содержание Coats 4050A

















Отзывы: