Hemisphere GPS V102 G страница 14 Скачать руководство пользователя | Manualshive

Страница: 14 / 60

background image

V102 GPS Compass User Guide

9

Mounting Orientation

The V102 outputs heading, pitch, and roll readings regardless of the
orientation of the antennas. However, the relation of the antennas to the
boat’s axis determines whether you will need to enter a heading, pitch, or
roll bias. The primary antenna is used for positioning and the primary and
secondary antennas, working in conjunction, output heading, pitch, and roll
values.

Note:

Regardless of which mounting orientation you use, the V102 provides

the ability to output the heave of the vessel. This output is available via the
$GPHEV message. For more information on this message refer to refer to
GPS Technical Reference available from the Hemisphere GPS website at

www.hemispheregps.com

.

Parallel Orientation:

The most common installation is to orient the V102

parallel to, and along the centerline of, the axis of the boat. This provides a
true heading. In this orientation:

•

If you use a gyrocompass, you can enter a heading bias in the V102
to calibrate the physical heading to the true heading of the vessel.

•

You may need to adjust the pitch/roll output to calibrate the
measurement if the Vector is not installed in a horizontal plane.

Perpendicular Orientation:

You can also install the antennas so they are

oriented perpendicular to the centerline of the boat’s axis. In this orientation:

•

You will need to enter a heading bias of +90° if the primary antenna
is on the starboard side of the boat and -90° if the primary antenna
is on the port side of the boat.

•

You will need to configure the receiver to specify the GPS antennas
are measuring the roll axis using $JATT,ROLL,YES.

•

You will need to enter a roll bias to properly output the pitch and roll
values.

•

You may need to adjust the pitch/roll output to calibrate the
measurement if the Vector is not installed in a horizontal plane.

«
...
12
13
14
15
16
...
»

Содержание V102 G





























































Отзывы:

Нет отзывов

Похожие инструкции для V102 G

Бренд: DAPAudio Страницы: 12

Бренд: Octet Matrix Audio Страницы: 14

Бренд: Agilent Technologies Страницы: 174

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 14

Бренд: Philips Страницы: 14

Бренд: Philips Страницы: 18

Бренд: Philips Страницы: 15

Бренд: Philips Страницы: 22

Бренд: Philips Страницы: 20

Бренд: Philips Страницы: 22

Бренд: Philips Страницы: 32

Бренд: Philips Страницы: 30

Бренд: Philips Страницы: 35

Бренд: Samsung Страницы: 11

SoundTower TW-H5500

Бренд: Samsung Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды