Hemisphere GPS V102 G страница 51 Скачать руководство пользователя

Страница: 51 / 60

Appendix B: Specifications

Table B-1 through Table B-5 provide the V102’s GPS sensor, communication,
power, mechanical, and environmental specifications.

Table B-1: GPS sensor specifications

Item

Specification

Receiver type

L1, C/A code with carrier phase smoothing

Channels

Two 12-channel, parallel tracking
(Two 10-channel when tracking SBAS)

SBAS tracking

2-channel, parallel tracking

Update rate

Standard 10 Hz, optional 20 Hz (position and
heading)

Horizontal accuracy

< 1.0 m 95% confidence (DGPS

)

< 2.5 m 95% confidence (autonomous, no SA

)

Heading accuracy

< 0.75° rms

Normal operation: GPS
Coasting (no GPS): Gyro

Heave accuracy

< 30 cm rms

Normal operation: GPS
Coasting (no GPS): None

Pitch accuracy

< 1.5° rms

Normal operation: GPS
Coasting (no GPS): Inertial sensor

Roll accuracy

< 1.5° rms using accelerometer

Normal operation: Inertial sensor
Coasting (no GPS): Inertial sensor

Rate of turn

/s maximum

Cold start

< 60 s typical (no almanac or RTC)

Warm start

< 20 s typical (almanac and RTC)

Hot start

< 1 s typical (almanac, RTC, and position)

Содержание V102 G





























































Результаты поиска

Содержание V102 G

Отзывы:

Похожие инструкции для V102 G

Бренды по названию

Популярные бренды

Hemisphere GPS V102 G, Руководство пользователя

Результаты поиска

Содержание V102 G

Отзывы:

Похожие инструкции для V102 G

Бренды по названию

Популярные бренды