manualshive.com logo in svg

Helwett Packard HP 8512A, Руководство пользователя

Поделиться
Скачать
Helwett Packard HP 8512A Скачать руководство пользователя страница 23

2.

Connect an open (or short) to port 1 and port 2.

3.

Press [User 

1 al], [User 

2 

 [User 

3 

 

and 

[User 

4 

bl] 

to check the channels indicated.

The b, and   traces should resemble Figure 3-3. The a, and   traces should resemble Figure 3-4.

Figure 3-3.

Typical Operator’s 

Check CRT Power Level Trace

 

 

4.

Connect a thru (two test port return cables) from port 1 to port 2.

5. Press PARAMETER 

[MENU] [USER 4 bl] [REDEFINE PARAMETER] [DRIVE] [PORT 

[PHASELOCK] 

 [REDEFINE DONE] 

to observe the bl thru power level trace. The trace should

resemble Figure 3-4.

 

 

6. Leave the thru connection of step 4 connected. Press PARAMETER 

[MENU] [USER 2 

[REDEFINE PARAMETER] [DRIVE] [PORT   [PHASELOCK] [al] [REDEFINE DONE] 

to observe

the b2 power level trace. The trace should resemble Figure 3-4.

Make sure that you redefine the parameters to the original conditions for al, bl, a2, and b2.

7.

If any of the traces are not within the specified limits, check all of the connections and repeat the

above procedure. If symptoms persist, refer to the Service Overview section of the 

Service Manual 

or volume 4 of the HP 8510A manual set.

HP 

 Test 

Operation

3-5

Содержание HP 8512A













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды