Hellenbrand H200M HE Скачать руководство пользователя страница 22

Страница: 22 / 44

STEP 5CS – This display will be available to select the use of an outside signal to control the initiation

of a regeneration. Selection only matters if a connection is made to the two pin connector labeled DP

SWITCH located on the printed circuit board. Following is an explanation of the options:

• IMMED REGEN – If the dP switch is closed for an accumulative time of 2 minutes, a regeneration will

occur immediately.

• DELAY REGEN – If the dP switch is closed for an accumulative time of 2 minutes, a regeneration will

occur at the schedule regeneration time.

• HOLD REGEN – If the dP switch is closed a regeneration will be prevented from occurring.

• OFF - Factory setting is off

Press NEXT to go to Step 6CS. Press REGEN to return to previous step.

STEP 6CS – Press the





buttons until selection of first cycle appears in left upper corner, in this

example FILL is selected. Press NEXT to go to Step 7CS. Press REGEN to return to previous step.

STEP 7CS – Press the





buttons until selection of second cycle appears in left upper corner, in

this example SOFTENING is selected. Press NEXT to go to Step 8CS. Press REGEN to return to previ-

ous step.

STEP 8CS – Press the





buttons until selection of third cycle appears in left upper corner, in this

example REGENERANT DRAW UP is selected. For a H200M HE control valve: prior to selecting DN or

UP or not selecting a regenerant flow cycle, verify the correct valve body, main piston, regenerant piston

and stack are being used and the injector or injector plug(s) are in the correct location. Press NEXT to go

to Step 9CS. Press REGEN to return to previous step.

STEP 9CS – Press the





buttons until selection of fourth cycle appears in left upper corner, in this

example BACKWASH is selected. Press NEXT to go to Step 10CS. Press REGEN to return to previous

step.

OFF

AUXILIARY INPUT

SET

REG

STEP 5CS

➔

[!J

EJEJEJ [!7

CYCLE 1

FILL

SET

STEP 6CS

➔

CYCLE 2

SOFTENING

SET

STEP 7CS

➔

CYCLE 3

REGENERANT DRAW UP

SET

STEP 8CS

➔

[!J

EJEJEJ [!7

[!J

EJEJEJ [!7

[!J

EJEJEJ [!7

CYCLE 4

BACKWASH

SET

STEP 9CS

➔

[!J

EJEJEJ [!7

Содержание H200M HE













































Результаты поиска

Содержание H200M HE

Отзывы:

Похожие инструкции для H200M HE

Бренды по названию

Популярные бренды

Hellenbrand H200M HE, Руководство пользователя

Результаты поиска

Содержание H200M HE

Отзывы:

Похожие инструкции для H200M HE

Бренды по названию

Популярные бренды