Hellenbrand H200M HE Скачать руководство пользователя страница 14

Страница: 14 / 44

SERVICE REMINDER

STEP 14S – Set scheduled service display using





buttons. Available options are OFF, TIME, ON GAL

or BOTH. Selecting OFF disables this feature. If OFF is selected, press NEXT to exit System Setup. If

TIME, ON GAL or BOTH is selected press NEXT to select the TIME and/or ON GAL values. This can also

activate relay if Service Alarm is selected. Press REGEN to return to the previous step.

STEP 15S – Service alarm for TIME ranges from 0.25 to 9.75 years. Use





buttons to select length

of time between service reminders. Press NEXT to either exit System Setup or if BOTH was selected go

to Step 25S. Press REGEN to return to the previous step. When time selected and # of days drops below

1 year, the next display will show “scheduled service in XXX days” after screen where service reminder is

programmed.

STEP 16S – Service alarm for ON GAL ranges from 100 to 9,999,000 gallons. Hold





buttons until

display flashes “SET” before releasing to select values. Press NEXT to see “Gallons until service” displays.

Press NEXT to exit system. Press REGEN to return to the previous step.

Reset service reminder by holding down up and down arrows together when reminder is displayed.

SERVICE ALARM

➔

SET

BOTH

STEP 14S

SCHEDULED SERVICE

➔

SET

0.25

STEP 15S

SCHEDULED SERVICE

➔

SET

80000

STEP 16S

GAL

RETURN TO NORMAL MODE

RELAY 1 SET POINT

➔

SET

GAL

RELAY 1 DURATION

➔

SET

0:01

MIN

SERVICE ALARM

➔

SET

GALLONS

➔

SET

STEP 13S

If Service Alarm chosen to activate relay, relay closes whenever Service Alarm has triggered.

Programming for relay closure on service reminder is done on Step 14S. Relay opens when

service alarm reset. Press NEXT to go to next step to set Relay 2 Settings. If off selected for

Relay 2, Press NEXT to go to step 14S for service reminder programming.

• Relay closes on Gallons

• Relay closes on Time

• Relay closes on Both

• Off

STEP13S –

Relay 2 programming includes identical options as Relay 1 with the addition of the ability

to trigger Relay 2 in Error Mode. Relay closes when ever control enters Error Mode and immediately

deactivates when error resolved and control reset. Press NEXT to go to Step 14S.

Use up and down arrows to select number of gallons per relay activation of regen gallon setting.

Range: 1 -100 gallons. Press NEXT to go to next step.

If Off or Time was selected in previous steps, this screen does not appear. Use up and down

arrows to set duration of relay activation in minutes. Range = 1 second - 500 minutes. Press

NEXT to go to Step 22S. Press REGEN to return to previous step. Meter does not read during

regeneration.

[!J

EJEJEJ [!7

[!J

EJEJEJ [!7

[!J

EJEJEJ [!7

[!J

EJEJEJ [!7

[!J

EJEJEJ [!7

[!J

EJEJEJ [!7

[!J

EJEJEJ [!7

RELAY 1

RELAY 2

Содержание H200M HE













































Результаты поиска

Содержание H200M HE

Отзывы:

Похожие инструкции для H200M HE

Бренды по названию

Популярные бренды

Hellenbrand H200M HE, Руководство пользователя

Результаты поиска

Содержание H200M HE

Отзывы:

Похожие инструкции для H200M HE

Бренды по названию

Популярные бренды