Heliocol HC10.5 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 29

Heliocol HC10.5 Скачать руководство пользователя страница 4

Table of Contents

Introduction

Welcome to the Heliocol Family

Heliocol Solar Collectors are manufactured utilizing state-of-the-art solar technology and the
most advanced production techniques. Heliocol collectors are sleek and simple, yet the pat-
ented over-molded design makes Heliocol durable enough to last a lifetime. However, a pro-
fessional installation is very important to the overall success of a system. Installed properly, a
Heliocol System will be virtually maintenance free as it captures free, abundant and reliable
heat from the sun year after year. Whether you are a seasoned contractor or a homeowner
installing your own system, this manual will give you a great deal of valuable information.

Take time to read through this manual. It will guide you through the most efficient way to cor-
rectly install a Heliocol Solar System. By following this step by step guide, your system will
meet the installation standards recommended by the factory (see disclaimer on page 1). In
addition, because we’ve included techniques and tips gathered from experienced Heliocol
contractors throughout the country, using this installation guide will save you time and effort.

2

Introduction
Getting Started
Collectors and Installation Kits
Parts List
Solar Collector Layout and Hydraulics
Connecting the Solar
Mounting the Solar Collectors on a Flat Roof
Assembly of Row Spacer Kits
Connecting the Solar Collectors to the Feed and Return Lines
Running the Feed and Return Lines from the Roof to Ground Level
How to Connect the Solar Collectors to the Existing Pool Filtration System
Pressure Testing the Heliocol Solar System
Operating and Check-Out Procedures
Installation Troubleshooting
Specifications

2
3
5
6
7
12
13
14
15
16
18
20
21
22
24

«
...
2
3
4
5
6
...
»

Содержание HC10.5






























Отзывы:

Нет отзывов