Heliocol HC10.5 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 29

Heliocol HC10.5 Скачать руководство пользователя страница 3

Disclaimer:

Before attempting installation, read these instructions carefully. This manual contains easy to follow step-by-
step procedures to properly install a Heliocol system. A little time spent understanding the system and its parts
will assure a successful, trouble-free installation. If you have any product or installation questions regarding this
system, contact your Heliocol Representative. When working on or around your roof or pool, please take care
to avoid hazards such as electrical wires and loose shingles or tiles. CAUTION! Safety comes first!

It is important to recognize that this manual outlines the recommended installation methods and practices as
prescribed by the factory. It is designed to aid a seasoned contractor or novice do-it-yourself individual while
providing optimum protection for the products. It is not designed to override any local codes or ordinances.
Also, these are the minimal requirements; additional hardware or protection may be required in hazardous
environments or in areas subject to extremes of weather or microburst climate events. In those areas, the lo-
cal expertise of the contractor may be relied upon in coordination with factory approval for special installation
considerations.

1

«
1
2
3
4
5
...
»

Содержание HC10.5






























Отзывы:

Нет отзывов