background image

13

ADJUSTING THE THROTTLE CURVE IN NORMAL

  

The throttle curve can be adjusted to optimize the  power to the motor depending on 
stick position and blade load.

1. Turn on your transmitter.

2. Press the MODE button for one second. You have entered model setup.

3. Turn the ADJUST dial until you see just the channel icons fl ash.

4. Press MODE or ENTER and just the fi rst adjustable channel will fl ash as well as the 
current value.

5. Turn the ADJUST dial until you reach Channel 3. The channel number will fl ash with 
dot below.

6. Press the MODE or ENTER button to activate the percentage value.

7. Rotate the ADJUST dial to scroll through the 5 dot points.

8. Press Mode or ENTER buttons to select (fl ashing) dot percentage you wish to change.

9. Press ENTER to save and move to the next dot. You may also use the ADJUST dial 
after pressing ENTER to expedite your selections.

10. To exit, press BACK to save and close.

ADJUSTING THE  UP-1 THROTTLE  CURVE

  

NOTE: The UP-1 Throttle curve is preset at the factory. Having said this you can use 
the HOV.T/FALP.T dial to adjust the UP-1 throttle curve from 51% to 100% power 
while the UP-1 switch is on.

To better explain the throttle curves let’s review the diagrams below. In the fi gure 
you can see three throttle curves. The one to the left is a typical throttle curve with 
the helicopter operating in normal mode. (The UP-1 switch off) The picture in the 
center shows the throttle curve with the transmitters UP-1 switch ON and the HOV.T/
FALP.T dial turned fully counter clockwise. The picture on the right shows the same 
condition with the HOV.T/FLAP.T dial turned fully clock wise. (This setting provides 
the most power to the motor with the UP-1 switch active.)

Possible "UP-1" Throttle Modes

Thr

ottle/Pitch Stick Mo

v

ement

50%

100%

0%

50%

100%

0%

Typical "Normal Mode"

5 Point Throttle Curve

1

2

3

4

5

Throttle Points (dot )

50%

100%

0%

50%

100%

0%

1

2

3

4

5

HOV.T/FLAP.T 

Rotate Dial Counter Clockwise

Throttle Points (dot )

50%

100%

0%

50%

100%

0%

1

2

3

4

5

HOV.T/FLAP.T

Rotate Dial Clockwise

Throttle Points (dot )

Содержание TX610

















Отзывы: