manualshive.com logo in svg

Heise PTE-1, Руководство по эксплуатации

Поделиться
Скачать
Heise PTE-1 Скачать руководство пользователя страница 8

- 8- 

Revision 4.6  3/2004

Section 3.0  

System Start-Up General 

 

 

Instructions

The HHC can perform a wide variety of simple and 
complex temperature and pressure based measurement, 
test and calibration operations. Due to the menu driven 
set up procedures the system can be quickly and easily 
confi gured for most any of its measurement functions. 
By following the steps in this section you can be ready 
to use your HHC to perform basic pressure and tempera-
ture measurement functions in a matter of minutes.

  Section 3.1 

Battery Installation

Step 1  

 To gain access to the battery compartment, 

remove the bottom end of the strap assembly by 
detaching the Velcro connection and pulling the bottom 
end of the strap from the retaining pin in the bottom of 
the case of the base unit. 

Step 2  

 Open the battery compartment by sliding the 

battery enclosure cover out of the compartment opening. 
To do this press down on the circular, ribbed indentation 
on the battery cover while pushing the enclosure cover 
outward with pressure on the two standoffs located near 
the pin used to retain the strap on the base unit.

Step 3 

 Note the polarity information for installation of 

the two 9 volt alkaline batteries as outlined on the inside 
of the battery enclosure.

Step 4 

 Locate the two 9 volt batteries and the foam 

retaining spacer provided in a small plastic bag. Install 
these batteries as shown on the diagram in the battery 
enclosure. The HHC will operate for approximately 30 
hours on the two 9 Vdc batteries. Alkaline batteries are 
recommended for use in the HHC system. 

Step 5  

 Insert the retaining spacer between the two 9 

volt batteries. This will insure that the batteries will not 
disconnect or be shaken loose during normal operation.

Step 6  

 Replace battery compartment cover by sliding 

cover back into position until it locks in place.

Step 7  

 Replace strap by threading strap through the 

programmed into the GQS-RT unit to provide enhanced 
accuracy. Each GQS-RT interface module can accom-
modate up to 8 different programmed RTD calibration 
curves. Programming of the RT module is accomplished 
via an optional  software package and any PC compat-
ible computer with an available  standard serial com-
munication port. See Appendix E page 75 for probe 
connector pin out information. 

  Section 1.4.4  The GQS-TC1 Quick Select
 

Thermocouple Interface Module

The GQS-TC1 allows the HHC base unit, when used 
with a thermocouple interface module, to perform 
temperature measurement. The GQS-TC1 plugs directly 
into the Quick Select module bay in the base unit. The 
thermocouple is then attactched to the GQS-TC1 module 
via a male “miniature thermocouple connector.” 

  Section 2.0 

Unpacking  & General Care

General instructions for unpacking and calibrator care 
follow. 

  Section 2.1  

Unpacking Product Upon Receipt

Prior to removing the HHC from the packaging material 
inspect all cartons for shipping damage. Document any 
damage evident in the event that a damage claim must 
be made against the shipper. After inspection, remove 
the base unit, module(s), manual and any accessories 
purchased from the packaging material. Retain the 
packaging for use in returning the HHC to the factory 
for future recertifi cation or repair.

  Section 2.2 

Product Storage

The product should be stored in an area that is main-
tained in the temperature range indicated in the storage 
temperature in the product specifi cation. The storage 
temperature limits are -4 to + 158 degrees Fahrenheit. 
Storage of product in environments that will exceed 
these temperature limits results in signifi cant risk of 
product damage.  It is recommended that the product 
not be left in closed cars or truck cabs as temperature 
damage can easily occur due to the “greenhouse effect” 
of closed vehicles or extreme cold temperatures that can 
result from winter conditions.

  Section 2.3  

Product Cleaning 

The enclosure of the calibrator is not watertight. As 
such, care should be taken during cleaning to assure 
liquid does not penetrate the enclosure for the base unit 
or Quick Select modules. Cleaning of the product should 
be done with a cloth moistened with a warm, mild deter-
gent mixture.

Содержание PTE-1

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды