STUDIO 1 12V v1 Jan 2020
Page
2
of
3
INSTALLATION OF STUDIO 1 12 volt LADDER TOWEL WARMER
SPECIFICATIONS
Mounting Centre
(Approx Width)
Rating at 12 Volts AC
Voltage
IP Rating
WSLV825 (7 Rungs)
570mm
86 Watts
12v
IP47
WSLV825S (7 Rungs) Slimline
420mm
68 Watts
12v
IP47
WSLV510E (5 Rungs)
820mm
84 Watts
12v
IP47
WSLV510 (5 rungs)
570mm
61 Watts
12V
IP47
This Package Contains:
1 Ladder Towel Warmer
1 x Concealed adaptor fixing barrel
4 x Mounting Screws to fix Fixing Barrels to wall
2 x Top Mounting Legs with Fixing Barrel & Grub Screw & (Separate) Fixing bolt
1 x Bottom Mounting Leg (Non Flex Leg) with Fixing Barrel & Grub Screw
1 x Bottom Mounting Leg (Flex Leg) with Plastic grommet & Flat Fixing Bracket & M4 x10 Screw
1x PVC white flex (for exposed wire installations)
!x termination pack ( 2 x bootlace crimps and heat shrink)
CAUTION:
Prior to installation please ensure the product is to your satisfaction. Once installed Heirloom cannot be responsible for defects in the
product finish. This product is not intended for use by young children or infirmed persons without supervision. Young children must be supervised
to ensure they do not play with the product. To minimize a hazard for young children, this appliance must be installed so that the bottom rail is
600mm above the floor. If the supply cord is damaged it must be replaced by the manufacturer, its service agent, or similarly qualified persons in
order to avoid a hazard.
Installation:
This towel warmer must be installed by a registered electrician and in accordance with local and national electrical codes. Use suitable size cable
for the installation We recommend that the towel warmer be installed vertically on a flat and uniform wall, and where possible into studs or other
suitable anchor material. If fixing to hollow cavity walls, Toggle Anchors (not those supplied) or similar devices must be used.
Position the towel warmer so that the towel warmer leads and flush box are easily accessible, with the cable entry to the towel warmer NEAREST
THE FLOOR. Avoid the supply cable coming into contact with the heated parts of the towel warmer.
DO NOT PLUG THE UNIT INTO THE POWER SUPPLY OR SWITCH THE TOWEL WARMER ON BEFORE INSTALLATION IS COMPLETE.
1
If the towel warmer is being installed with a concealed electric flex, read those instructions before returning to this point as preparatory
work is required before the wall cladding is installed on to the walls.
2
Identify the three different types of mounting legs per the above descriptions and attach the two top mounting legs to the towel warmer
with the fixing bolts (After removing the fixing barrels & making sure the grub screw will face the floor)
3
Decide which side the electric flex is to be conn
ected and then connect the “Non Flex” Leg to
the bottom of the towel warmer that will
not house the electric flex (After removing the fixing barrel & making sure the grub screw will face the floor). Also before attaching the
leg, shorten and insulate the wires on the side not being used.
4
Thread
the “Flex Leg” on to the electric flex (ensuring that the leg is facing in the correct direction). Fix the leg to the towe
l warmer with
the two screws provided.
5
If the warmer is being installed without using the concealed adaptor (i.e. the electric flex is to be visible) proceed to the next step. Use
the white tube, cut to length to cover the leads. If the towel warmer is being installed with a concealed wiring fixing adaptor, proceed to
that section.
6
Hold the towel warmer in position and mark around one of the top legs. Remove the towel warmer and fix the fixing barrel to the wall.
7
Ensuring that mounting points are level (horizontal), mark the second point. . Fix the mounting barrel to the wall. Should the towel
warmer not be sitting square, do not proceed further with installation without rectifying problem.
8
Place the towel warmer onto the two fixing barrels and mark the location of the two bottom legs.
9
Remove the towel warmer and fix the remaining fixing barrel and fixing bracket to the wall. Ensure that the metal fixing bracket is used
for the foot that contains the electric flex. (The other three feet will use the same style of fixing bracket)
10
A length of PVC flex is supplied for exposed flex installations. Use bootlace crimps and heat shrink to joint towel warmer leads to this
flex. Ensure the flex exits the leg through the slot with the plastic edge.
11
Place the towel warmer in position and secure it to the fixing barrels using the grub screws.
12
Connect the towel warmer leads to the supply from the transformer.
