manualshive.com logo in svg

Heinner VMF001, Инструкция по эксплуатации

Поделиться
Скачать
Heinner VMF001 Скачать руководство пользователя страница 7

 

7 

 

GASOLINE CHAIN SAW 

 

MAINTENANCE 

 

In order to maintain your product in proper working order, perform the maintenance and checking 
operations described in the manual at regular intervals. 

 

Always be sure to turn off the engine before performing any maintenance or checking procedures. 

 

 

WARNING 

The metallic parts reach high temperatures immediately after stopping the engine. 

 

Leave  all  maintenance  other  than  the  items  listed  in  the  owner’s  manual  to  your 

competent servicing dealer. 

 

 

TRANSPORTATION 

 

Always carry the unit with the engine stopped, the guide bar covered with the protector to the rear, 
and muffler away from your body. 

 

5. INSTALLING GUIDE BAR AND SAW CHAIN 
 

A standard saw unit package contains the items as illustrated. (F1) 

(1) Power unit    
(2) Bar protector 
(3) Guide bar    
(4) Saw chain  
(5) Plug wrench  
(6) Screwdriver for carburetor adjustment 
(7) Spike and mounting screws 

 
Open the box and install the guide bar and the saw chain on the power unit as follows: 
 

 

WARNING 

The saw chain has very sharp edges. Use thick protective gloves for safety. 
1. Pull the guard towards the front handle to check that the chain brake is not on. 
2. Loosen the nuts, and remove the chain cover. 
3. Install the attached spike to the power unit. 
4. Gear the chain to the sprocket and while fitting the saw chain around the guide bar, mount the guide bar 
to the power unit. adjust the position of chain tensioner nut on the chain cover to the lower hole of guide 
bar. (F2)

 

 

(8) Hole  
(9) Tensioner nut  
(10) Chain cover 
 
 

 
 

NOTE 

Pay attention to the correct direction of the saw chain. (F3) 
 

(1) Moving direction 
 

 

Содержание VMF001



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды