Heiniger Acutecc Euro Grinder Скачать руководство пользователя страница 18

Страница: 18 / 21

12.

Trouble shooting

Problem

Cause

Solution

For all electrical faults qualified

persons only may undertake fault

finding and repairs.

Motor doesn’t

No power.

Check the plug is correctly connected

start, switch light

to the socket.

is off.

Check that power is available at the

socket.

Call an electrician.

Motor stops,

The motor has overheated and

Allow the motor to cool.

Note:

When

switch light is on.

the internal thermal overload

the motor has cooled sufficiently if

has cut out.

the switch is still turned on it will

restart without warning.

Grinder vibrates.

Discs out of balance.

1) Emeries not in centre of

1) Reset with emeries in the centre.

disc.

2) Clean discs in soapy water.

2) Discs have glue on the

back.

3) Reset emeries with even glue

3) Uneven glue spread under

spread.

emeries.

4) Remove discs clean collar and

4) Foreign matter between disc

disc and replace.

and collar on shaft.

5) Replace disc.

5) Discs buckled.

Emeries won’t

1) Wrong glue used.

1) Use Heiniger shearer’s glue.

stick to discs

2) Old glue used.

2) Use new Heiniger shearers glue.

3) Wash in hot soapy water.

3) Discs have film of foreign

matter on them (oil, dirt,

grease, old glue etc).

4) Buy new disc or clamp plate.

4) Disc or clamp plate buckled.

13.

Material groups

Please be aware of the relevant regulations applicable in your country when disposing
of discarded parts. Refer to

14. Component illustration

Material

Contained in position

Iron/steel

1, 3, 14, 15, 16, 17, 20, 22, 23, 24, 27

Aluminium

1, 7, 25, 26

Copper

Stainless steel

10, 13

Polyethylene

ABS

8, 9, 11, 12, 19

Rubber

Содержание Acutecc Euro Grinder






















Результаты поиска

Содержание Acutecc Euro Grinder

Отзывы:

Бренды по названию

Популярные бренды

Heiniger Acutecc Euro Grinder, Руководство пользователя

Результаты поиска

Содержание Acutecc Euro Grinder

Отзывы:

Бренды по названию

Популярные бренды