background image

 

13 

 

GUARANTEE 

We  the 

Electric Central Heating Company

 guarantee that should this electric combination boiler prove 

to be defective by reason of faulty workmanship or material within 24 months of the date of purchase, we 
will replace the defective parts free of charge on condition that :- 
 
1. 

The boiler has been correctly installed and used only on the supply circuit or voltage stamped on 
the rating plate. 

 
2. 

The boiler has been used and serviced in accordance with these instructions and has not been 
tampered with or otherwise subject to misuse, neglect or accident. 

 
3. 

The appliance has not been taken apart, modified or repaired by a person other than authorized by –
Electric Central Heating Company (Heatwell)Ltd 

 
4. 

Evidence of the date of purchase and annual maintenance checks in the form of an invoice, receipt 
(or hire purchase documents) is required if service under guarantee is required. Any service under 
guarantee will not alter the original expiry date at the end of the 24 month period 

 
5. 

Warranty registration card must be completed and returned to register your guarantee.  
Failure to do so may result in a delay should any fault arise

 
6. 

Scale will build up in hard water areas with a boiler operating at high temperature such as this one. 
We there for strongly recommend that scale inhibitors are fitted to protect the boiler. The 
manufacturers guarantee does not extend to cover this natural phenomenon 

 

In the event of any difficulties please contact Technical Services 

Head Office & Manufacturer

 

England  Phone   0115 968 1273

 

Scotland Glasgow Office

                       

Phone  0141 944 0440

 

               Electric Central Heating Company  (Heatwell)

 

Emtex House 

 

 

 

 

 

Unit 51 

 

Benneworth Close 

 

 

 

 

42 Dalsetter Avenue 

Hucknall 

 

 

 

 

 

 

Glasgow  G15 8TE 

Nottingham  NG15 6EL   

 

 

Tel  0141 944 0440

 

Tel  0115 968 1273   

 

 

 

 

Fax  0115 968 0464   

 

 

 

email. 

[email protected]

 

web.

   www.heatwell.co.uk

 

 
 
 
 

Содержание 215 DSS/12Kw


















Отзывы: