Heatstore HSR115 Скачать руководство пользователя страница 10

Страница: 10 / 12

NOTE:

Use only Heatstore approved spare parts. Replacement of any parts with

components not recommended by Heatstore will invalidate the guarantee and may

render the installation dangerous.

7.0 SPARE PARTS

The following spare parts are available for your Heatstore water heater. Please refer to

the Rating Label on the bottom of your heater before ordering to ensure the correct

spare part is obtained.

IMPORTANT NOTE

On all heaters installed outside the UK it is essential to quote all the model details on

the rating label especially voltage and kW rating.

DO NOT REPLACE WITH PARTS NOT RECOMMENDED BY HEATSTORE -

THIS WILL INVALIDATE YOUR GUARANTEE AND MAY RENDER THE

INSTALLATION DANGEROUS.

DESCRIPTION

CODE NO.

Heaterplate Gasket ...............................................

S101

Drain Screw & Washer .........................................

S124

Thermal cut-out ....................................................

S567

Heaterplate Assembly c/w Thermostat & Cut-out

S3407

Feed Pan Cover 25 litre ........................................

S3408

Feed Pan Cover 45 litre & 70 litre .........................

S3409

Feed Pan Cover 115 litre .......................................

S3411

Bylaw 30 Kit .........................................................

S3412

Float Valve Assembly ...........................................

S5512

Control Thermostat ..............................................

95980025

Содержание HSR115













Результаты поиска

Содержание HSR115

Отзывы:

Бренды по названию

Популярные бренды

Heatstore HSR115, Инструкция пользователя

Результаты поиска

Содержание HSR115

Отзывы:

Бренды по названию

Популярные бренды