manualshive.com logo in svg

Heatrae Sadia HANDY NO-TOUCH, Инструкция по установке и руководство пользователя

Поделиться
Скачать
Heatrae Sadia HANDY NO-TOUCH Скачать руководство пользователя страница 15

15

9.0 FAULT FINDING

9.1   In the unlikely event of a problem, consult the trouble-shooting chart  

 

below.

9.2   If you are unable to remedy the problem, CONTACT YOUR  

 

 

INSTALLER in the first instance.

 

IMPORTANT

9.3   Do not attempt any electrical or plumbing work unless you are  

 

 

competent to do so.

9.4   If you still cannot solve the problem, please contact Heatrae Sadia.  

 

INSPECTION

9.5   It is advisable that, in the interests of safety, the handwash and its    

 

electrical installation is checked by a competent electrician, at least  

 

every two years.

SYMPTOM

POSSIBLE CAUSE

REMEDY

A. Water supply turned off

Turn on water supply

B. Unit frozen

Turn OFF ELECTRICITY at isolating switch
and contact installer. DO NOT USE THE
HANDWASH.

C. Spout blocked

Clean sprayplate - see 10.2

D. Filter blocked

Clean filter

E. Electrical power to 
    appliance off
A. Torx adjusting screw at 

Turn torx screw clockwise until temperature

     wrong setting

is comfortable

B. Water flow too high

Turn torx screw clockwise until temperature 
is comfortable

C. Poor flow

Check inlet pressure

A. Torx adjusting screw at 

Turn torx screw fully anticlockwise to increase

    wrong setting

flow and lower temperature

B. Spout partially blocked

Clean sprayplate - see 10.2

C. Isolating valve not fully 

Open isolating valve

    open
D. Filter blocked

Clean filter

A. Spout blocked

Clean sprayplate - see 10.2
Push plastic plunger up and back in place.

    pressure relief

B. Spout not blocked

Call a service engineer, as there may be a
problem with internal parts.

Ensure that the electricity supply to the 
appliance is switched on

    with valve open

    device

1. No water flows     

2. Water too cold

3. Water too hot

4. Water runs from

Fault Finding Table

Содержание HANDY NO-TOUCH





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды