Heatilator ST42A Скачать руководство пользователя страница 29

Страница: 29 / 52

Heatilator • ST42A US-CAN • 4012-039 Rev D • 11/07

12 in.
(305 mm)
max.

12 in.
(305 mm)
min.

Gas

Knockout

50 deg.

37 deg.

Brick

Front

48 in.

(1219 mm)

(framing)

42 in.

(1067 mm)

(opening)

9-3/4 in.

(248 mm)

14-3/8 in.

(365 mm)

12 in.

(305 mm)

4 in.

(102 mm)

Flush
Front

12 in.

(305 mm)

Figure 8.5 Sidewalls/Surrounds

Fire Risk

Do NOT obstruct air inlet or outlet grilles.
Do NOT modify grilles.
• Modifying or covering grilles could cause

temperature rise and

re hazard.

Finishing materials must not interfere with:
• Air

ow through grilles or louvers

• Operation of louvers or doors
• Access for service

WARNING

Figure 8.4 Mantel Speci

cations

Fire Risk

Finish all edges and fronts to clearances and
speci

cations.

WARNING

• Metal fireplace front may be covered with non-

combustible material only.

• Do NOT overlap combustible materials onto

replace

fronts.

• Install combustible materials up to speci

ed clearances

on top, front and side edges.

• Seal joints between the

nished wall and

replace top

and sides using only a 300° F minimum sealant.

E. Glass Doors

This

replace has been tested and listed for use with doors

as speci

ed in Section 12.B. Fireplace Components. Please

refer to the manual packed with each set of doors for instal-
lation instructions.

D. Sidewalls/Surrounds

Adjacent combustible side walls must be located a minimum
of 12 in. (305 mm) from the

replace opening. If you are us-

ing a decorative surround constructed of combustible ma-
terial, it must be located within the shaded area de

ned in

Figure 8.5. Short stub walls are also acceptable if they are
contained within the shaded area.

C. Mantel

A combustible mantel may be positioned no lower than
12 in. (305 mm) above the top of the

replace openings. The

combustible mantel may have a maximum depth of 12 in.
(305 mm). Combustible trim pieces that project no more than
1 in. (25 mm) from the faces of the

replace can be placed

no closer than 6 in. (152 mm) from the top of the

replace

openings. See Figure 8.4. Combustible trim must not cover
the metal surfaces of the

replace. This mantel clearance is

in accordance with

Section 7-3.3.3 of ANSI/NFPA211

Содержание ST42A





















































Результаты поиска

Содержание ST42A

Отзывы:

Похожие инструкции для ST42A

Бренды по названию

Популярные бренды

Heatilator ST42A, Руководство пользователя

Результаты поиска

Содержание ST42A

Отзывы:

Похожие инструкции для ST42A

Бренды по названию

Популярные бренды