Heatilator ST42A Скачать руководство пользователя страница 15

Страница: 15 / 40

Heatilator • ST42A Installation Manual • 4012-051 • Rev C • 10/03/13

d & g

Ceiling Firestop

58-7/8 in.

(1495 mm)

Effective

Height

a,b,c,f

11-10 in. (279-254 mm)

adapter required in

Canada.

Figure 4.1 Chimney Requirements

NOTICE:

A maximum of two pairs of offsets and returns

may be used.

WARNING! Risk of Fire!

You must maintain 2 in. (51 mm)

air space clearance to insulation and other combustible

materials around the chimney system. Failure to do so

may cause overheating and fire.

NOTICE:

You must provide support for the pipe during

construction and check to be sure inadvertent loading has

not dislodged the chimney section from the fireplace or at

any chimney joint.

A. Chimney Requirements

Vertical distances are measured from the base of the

fireplace as shown in Figure 4.1.

Chimney and Termination Requirements

Table 4.2 Chimney Component Dimensions

Table 4.1 Chimney Requirements

meters

a. Minimum overall straight height

14.0

4.27

b. Minimum height with offset/return

16.5

5.03

c. Maximum height

90.0

27.43

d. Maximum chimney length between an offset and

return

20.0

6.1

e. Maximum distance between chimney stabilizers

35.0

10.67

f. Double offset/return minimum height

22.0

6.71

g. Maximum unsupported chimney length between the

offset and return

6.0

1.83

h. Maximum unsupported chimney height above the

fireplace

35.0

10.67

i. Maximum unsupported chimney above roof

6.0

1.83

HEIGHT OF CHIMNEY COMPONENTS

in.

Canada ONLY

Chimney Stabilizer

SL11

SL4

4-3/4

121

Offsets/Returns

SL1130

SL430

14-1/2

368

Chimney Sections*

SL1106

SL406

4-3/4

121

SL1112

SL412

10-3/4

273

SL1118

SL418

16-3/4

425

SL1136

SL436

34-3/4

883

SL1148

SL448

46-3/4

1187

n/a

SLA10

16-3/4

425

* Dimensions reflect effective height.

Содержание ST42A









































Результаты поиска

Содержание ST42A

Отзывы:

Похожие инструкции для ST42A

Бренды по названию

Популярные бренды

Heatilator ST42A, Руководство по установке

Результаты поиска

Содержание ST42A

Отзывы:

Похожие инструкции для ST42A

Бренды по названию

Популярные бренды