Heatilator Gas Fireplace GDCL4136I Скачать руководство пользователя

Страница: 55 / 84

Heatilator • GDST4336I, GDFL4136I, GDCR4136I, GDCL4136I • 2129-900 Rev. W • 12/15

Step 5. Fold bottom

ap along score line as indicated in

Figure 13.6 and tuck into valve access area of appliance.
Splatter guard should

t securely on front of unit.

Figure 13.6 Folding Bottom Flap

Once plumbing and wiring are complete on the

replace,

the lower access panel may be closed until the time that the
splatter guard must be removed for

ring the appliance.

Figure 13.7 Prepare to Open Lower Access Panel

Step 6. To open lower access panel of splatter guard, place
one hand above score line and place two

ngers from other

hand in the round holes on the front of the splatter guard.
See Figure 13.7. Pull out and fold up the panel as shown
in Figure 13.8. Disengage the tabs on left and right bottom
of splatter guard and

t them into the square holes. The

tabs are now inside the front of the splatter guard; carefully
bend them down. See Figure 13.9.

Figure 13.9 Securing Tabs Inside Front of Splatter Guard

Figure 13.8 Opening Lower Access Panel

To Close the Lower Access Panel:

Carefully disengage the tabs from the square holes and
bend the access panel to its original position. Bend the
center bottom

ap and insert it into the bottom of the ap-

pliance.

To Remove the Splatter Guard:

Carefully grab splatter guard on or near the vertical center
on the left and right sides. Pull outward gently, but

rmly,

taking care not to tear or remove the inserted tabs.

Figure 13.11 Splatter Guard with Lower Access Panel Closed

Figure 13.10 Splatter Guard with Lower Access Panel Open

Содержание Gas Fireplace GDCL4136I





















































































Результаты поиска

Содержание Gas Fireplace GDCL4136I

Отзывы:

Похожие инструкции для Gas Fireplace GDCL4136I

Бренды по названию

Популярные бренды

Heatilator Gas Fireplace GDCL4136I, Руководство пользователя

Результаты поиска

Содержание Gas Fireplace GDCL4136I

Отзывы:

Похожие инструкции для Gas Fireplace GDCL4136I

Бренды по названию

Популярные бренды