Heatilator Gas Fireplace GDCL4136I Скачать руководство пользователя | Manualshive

Страница: 41 / 84

background image

41

Heatilator • GDST4336I, GDFL4136I, GDCR4136I, GDCL4136I • 2129-900 Rev. W • 12/15

C. Securing and Leveling the Appliance

WARNING! Risk of Fire!

Prevent contact with:

•  Sagging or loose insulation
•  Insulation backing or plastic
•  Framing and other combustible materials
Block openings into the chase to prevent entry of blown-
in insulation. Make sure insulation and other materials
are secured.

DO NOT

notch the framing around the appliance

standoffs.
Failure to maintain air space clearance may cause
overheating and

fi

re.

NOTICE:

Failure to ensure that the

fi

replace opening

is square may result in the decorative front not

fi

tting

properly.

The diagram shows how to properly position, level, and
secure the appliance (see Figure 9.9). Nailing tabs are pro-
vided to secure the appliance to the framing members.
1. Venting - refer to Vent Clearances and Framing (Section

8) for hole location.

2. See Figure 9.10 for LCOR and RCOR nailing tab

location.

3. Place the appliance into position, making sure to

maintain proper clearance to combustibles.

Figure 9.12 Securing An Appliance

NAILING TABS

Note:

Once appliance is setup for top or rear venting, it

CANNOT be changed at a later time.

Figure 9.11 Proper Positioning and Leveling of an Appliance

90º

SIDE T

O SIDE

FRONT T

O BACK

4. Level the appliance from side to side and front to back. It

is acceptable to use wood shims under the appliance.

Figure 9.10 Attach Nailing Tab to Front Corner of Unit

5. Fasten the appliance to the

fl

oor using the pilot holes

located at the bottom of the appliance.

6. Bend out nailing tabs on each side making sure to keep

the nailing tabs

fl

ush with the framing.

7. Using a framing square, make sure that the sides of

the appliance are square to the bottom as shown in
Figure 9.11.

8. Secure the appliance to the framing by using nails

or screws through the nailing tabs. It is acceptable to
use plumber strap to secure the unit to the framing if
necessary. See Figure 9.12. Be sure to maintain all
clearances to combustible material.

NAILING TAB

NAILING TAB

«
...
39
40
41
42
43
...
»

Содержание Gas Fireplace GDCL4136I





















































































Отзывы:

Нет отзывов

Похожие инструкции для Gas Fireplace GDCL4136I

Бренд: Harman Страницы: 10

Бренд: LAMBORGHINI Страницы: 40

Бренд: Majestic Страницы: 40

Бренд: Pacific energy Страницы: 28

Бренд: Dik Geurts Страницы: 96

Prescott White Mantel

Бренд: Early Settler Страницы: 4

Бренд: Desa Страницы: 16

Бренд: Superior Страницы: 8

Бренд: Rinnai Страницы: 36

Бренд: Rinnai Страницы: 36

Slimfire Zero Clearance Box

Бренд: Rinnai Страницы: 2

Бренд: Rinnai Страницы: 32

Бренд: Blumfeldt Страницы: 36

Бренд: White Mountain Hearth Страницы: 12

Бренд: PERFECTION-SCHWANK Страницы: 40

Бренд: Megamaster Страницы: 20

Бренд: Quadra-Fire Страницы: 36

Бренд: Quadra-Fire Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды