3
598-1153-02
SPECIFICATIONS
Horizontal Range . . . . Up to 70 ft. (21 m); 100 ft.
(30.5 m) with Range Boost.
[varies with surrounding
temperature]
Vertical Range . . . . . . Up to 15 ft. (4.6 m)
Sensing Angle . . . . . . Up to 240° horizontal. Up to 80°
Vertical
Electrical Load . . . . . . Up to 500 Watts Maximum In-
candescent
Power Requirements . 120 VAC, 60 Hz
Operating Modes . . . . TEST, AUTO and MANUAL
MODE
Time Delay . . . . . . . . 1, 5, 20 minutes
D
ual
B
rite
®
Timer . . . . Off, 3, 6 hours, Dusk-to-Dawn
HeathCo LLC reserves the right to discontinue prod-
ucts and to change specifications at any time without
incurring any obligation to incorporate new features in
products previously sold.
Bottom of Sensor
Avoid aiming the sensor at:
• Objects that change temperature rapidly, such as
heating vents and air conditioners.
These heat
sources could cause false triggering.
• Areas where
pets or traffic
may trigger the control.
•
Nearby large, light-colored objects
reflecting light
may trigger the shut-off feature. Do not point other
lights at the sensor.
MAX
MIN
RANGE
ON-TIME
DUAL BRITE™
TEST 1 5 20
MINUTES
OFF 3 6 DUSK TO
DAWN
HOUR
BO
O
S
T
❒
Loosen the clamp screw
in the sensor ball joint and
gently rotate the sensor.
❒
Walk through the coverage
area noting where you are
when the lights turn on (also,
the LED will flash several
times when motion is detect-
ed). Move the sensor head up,
down, or sideways to change
the coverage area.
Keep the
sensor at least 1" (25 mm)
away from the bulbs.
❒
Adjust the RANGE as needed.
RANGE set too high may
increase false triggering.
❒
Secure the sensor head's
aim by tightening the clamp
screw.
Do not overtighten the
screw.
❒
Set the amount of TIME you want the lights to stay
on after motion is detected (1, 5, or 20 minutes).
❒
Set the D
ual
B
rite
®
switch to the amount of time
after dusk you want the lights on at low level (Off,
3, 6 Hrs., Dusk-to-Dawn).
Clamp
Screw
Ball
Joint
Aim Sensor
Down for Short
Coverage
Aim Sensor
Higher for Long
Coverage
Maximum
Maximum Range
Coverage Angle
Motion
Motion
15 ft.
(4.6 m)
70 ft. 100 ft.
(21 m) (30.5 m)
Boosted
Sensor
240°
D
ual
Z
one
™
D
ual
Z
one
™
D
ual
Z
one
™
D
ual
Z
one
™
NOTE:
D
ual
Z
one
™ is a new zone of detection which
was added as an option to select Heath
®
/Zenith motion
sensing products. This feature adds a zone of detec-
tion under the motion sensor. D
ual
Z
one
™ requires
no additional adjustment and operates in conjuction
with the forward-looking sensor.
Least Sensitive
Most Sensitive
NOTE:
If fixture is mounted higher than 8 ft. (2.4 m), aiming
the sensor down will reduce coverage distance.
The detector is less sensitive to motion directly towards it.
TEST AND ADJUSTMENT
❒
Turn on the circuit breaker and light switch.
NOTE:
Sensor has a 1
1
/
2
minute warm up period
before it will detect motion. When first turned
on, wait 1
1
/
2
minutes.
❒
Turn the RANGE control to the medium position
(halfway between MIN and MAX),D
ual
B
rite
®
OFF,
and the ON-TIME control to the TEST position.
WARNING - Risk of fire. Do not aim the bulbs
at a combustible surface within 3 ft. (1 m).
