PLUG-IN ROOM TEMPERATURE CONTROLLER
HEATERMATE
TM
Model HY02TP
Thank you for choosing
HEATERMATE
. This electronic temperature controller will provide you with
comfortable home environment and will help you to save energy.
QUICK START-UP GUIDE:
Plug HEATERMATE into power point
– a display showing current ROOM temperature and SET temperature
will come up. By pressing Up or Down buttons select your desired SET temperature. Plug your heater into
Heatermate. If child lock is activated press/hold Down button for 3 seconds then release to unlock.
BUTTONS EXPLAINED:
NO.
Symbols
Explanation
1
Power ON/OFF
2
Short press to switch between Manual and Automatic Modes
3
Press to Enter/Confirm
4
Increase (Up) Button
5
Decrease (Down) Button
6
Indicator
Light is ON -- power to heater is ON; light is OFF -- power to heater is OFF.
DISPLAY SYMBLES EXPLAINED:
NO.
symbols
Explanation
1
Automatic control mode (manual control
“ ” is not showing)
2
Manual control mode (automatic control
“
” is not showing)
3
Heating mode; “
” is displayed when power to heater is ON
4
Cooling mode; “
” is displayed when power to air conditioner or fan is ON
5
6 periods programmable icon
8
Room temperature
9
Child lock: activated automatically after 10 minutes of inactivity. Press/hold Down button
“
”
for 3
seconds then release to unlock. Repeat the same procedure to lock.
10
Ventilation mode
– turns heater off for a specified period of time during room ventilation (opening
windows) when room temperature drops below a specified temperature.
11
Clock setting icon
DISPLAY OVERVIEW:
1) Operation - Heating
Heatermate will turn your heater ON when ROOM temperature drops 1 degree below SET temperature and will turn your
heater OFF when ROOM temperature rises 1 degree above SET temperature. This 2 degrees temperature differential (which
comes as default) can be increased or reduced based on your preference
– please refer to Section 6. Smaller differential will
lead to smaller room temperature fluctuations, but the heater will come ON/OFF more frequently and vice versa.
2) Clock Setting
Press/hold
“
” for 3 seconds then release to enter into setting screen. “
” icon is flashing. Press “
” to enter into clock
setting mode which displays minute, hour and day of the week. Minute is flashing.
P
ress “
” or “ ” to set minutes then press
“
” to save and move to hours. Set hours and day of the week in similar manner.
3) Timer Function
The Timer function is designed to enable customer to switch Heatermate ON for one fixed time period every day defined by
ON and OFF times. Outside of this time period Heatermate will be in OFF state (nothing will be showing on its display).
To set Timer press/hold
“
” for 3 seconds then release to enter into setting screen. Press“
”to select “
”(
will flash)
P
ress “
” or “ ” to set ON time. Press“
” to save then press“
”to select “
” and set OFF time. To disable Timer
function set both ON and OFF times to 00.00 (comes as default).
Example: Set Timer for heater to come ON at 10pm every night, maintain 21.0 degrees temperature and turn OFF at 7am.
(i) Set ON time to 22:00 and OFF time to 08:00 by following above steps; (ii) Set the SET temperature to 21.0 degrees C; (iii)
Turn Heatermate OFF by pressing Power button
– the display will go OFF. Heatermate will then stay OFF until 10pm, when it
will come back ON (the display will come up). It will then run until 7am, maintaining room temperature of 21.0 degrees. At 7am
it will turn itself OFF (the display will go OFF) until 10pm, when it will come back ON, and so on, every day.
NB
: The Timer ON/OFF times, once set, will apply to both Manual and Automatic Modes
4) Automatic Mode - Weekly Programming
Automatic Mode ( symbol is showing next to SET temperature) allows customer to program up to 6 periods with different
SET temperatures for every weekday and up to 2 periods for the weekend. The table below shows the factory pre-set periods
and their temperatures. If less than 6 periods per day are required, then the adjacent periods can be merged into one period as
illustrated in the Example below. When device is in Automatic Mode, the display will always be ON, showing the current period
