manualshive.com logo in svg

Heatcraft H-IM-QRC, Инструкция по установке и эксплуатации

Поделиться
Скачать
Heatcraft H-IM-QRC Скачать руководство пользователя страница 15

15

Electric Defrost Mode 

When a defrost is initiated, the EEV closes, the system is allowed to 
pumpdown and shut off. The evaporator fans are cycled off and the 
defrost heaters are energized. 

On multiple evaporator systems, all controllers must terminate their 
defrost, either on temperature or fail-safe time, before the master 
controller will end the defrost cycle.

There is a 2 minute condensate drain-down period after which the 
system is started for a refreeze period. The evaporator fan stays 
off (fan delay). The refreeze period will last until the evaporator 
suction temperature is at 28°F or 3 minutes has elapsed. After 
this sequence, the system is back in the refrigerating mode and 
evaporators fans are now running.

Air Defrost Mode 

The sequence is the same as for electric defrost except that there 
are no heaters and the evaporator fans run continuously. 

Alarms 

Heatcraft Quick Response Controller provides a set of dry contacts 
for use in signaling an alarm. These contacts can be connected to 
a light, a buzzer, a bell etc., which will be activated when an alarm 
condition occurs. When the Heatcraft Quick Response Controller is 
energized, the alarm contacts are OPENED. When an alarm condition 
is detected, the contacts are CLOSED.

Conditions under which the alarm contacts will close are: 
 
 

•   High Box Temperature – LED Display: 

  

A1

 - Room temperature has exceeded 

 

 

the Alarm High 

ALH

 value for the Alarm 

  time 

ALt

 programmed. 

 

•   Low Box Temperature - LED Display:  

  

A 2

 - Room temperature has dropped  

 

 

below the Alarm Low 

ALL

 

value for the  

  

Alarm time 

ALt,

 programmed 

 

Defrost / Alarms

Clearing Alarms 

Alarms 

A1

 – High Box Temperature and 

A 2

 – Low Box Temperature 

will clear automatically if the Box Temperature decreases or 
increases to below or above the Alarm setpoint temperature. 
Replacing the Room Sensor, Suction Sensor or Pressure Transducer 
will clear the 

A 4

 Alarm.

 

•   Input Fault – LED Display: 

A 4

 - Box  

 

 

Temp., Suction Temp., Pressure  

 

 

Transducer open or not installed. 

 

•  Power failure – Loss of power to the 

  Evaporator

Alarm Codes 

 

A 1

 

High Box Temp

 

A 2

 

Low Box Temp

 

A 4

 

Input Fault

 

   

 

Box Temp., Suction Temp., Pressure

   

 

Transducer open or not installed

  

Power Failure

Содержание H-IM-QRC









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды