manualshive.com logo in svg

heat-timer Multi-MOD Platinum, Инструкция по установке и эксплуатации, Страница: 27 / 60

Поделиться
Скачать
heat-timer Multi-MOD Platinum Скачать руководство пользователя страница 27

Multi-MOD Platinum with Space and Scheduling Installation and Operation Manual

 

27

HT# 059299-00 

A

•   The 4-20ma option is used with the 4-20mA temperature sensor 

(HT# 904160-00) .  These sensors can be configured to read temperatures 

up to 480°F / 268°C .  The user must set the 4ma and 20ma temperature 

range to match the sensor configuration .  These sensors' ranges must be 

set by Heat-Timer .  See "4-20mA Temperature Sensor Wiring" on page 18 .

•   Values that are higher than 21 .6mA shall read SHORT .  Values that are 

lower than 2 .4mA shall read OPEN .

SENSOR 4mA VALUE

0 F

[  

]

 SENSOR 20mA VALUE

0 F

[  

]

eMS INPuT MODe

(Available In Sensor Type = °F, °C, and any of the PSI options)

Setback, eMS Control  

Default: Setback

4mA Adjustable from 70ºF/21ºC to 200ºF/93ºC 

Default: 140ºF/ 60ºC

20mA Adjustable from 90ºF/32ºC to 240ºF/116ºC 

Default: 200ºF/ 93ºC

PReSS TO SeleCT:

 /<System Startup>/..../Sensor Type/EMS Input Mode/ EMS 4mA SP/..

•   Setback allows the Set Point to be adjusted manually .
•   EMS Control allows the set point to be sent remotely using 4-20mA 

signal .  The set point range must be set to match the EMS signal's set 

point range using the 4mA and the 20mA temperature settings .  See 

"External Set Point Wiring" on page 22 .

•   An active signal must be between 2 and 22mA .  Any signal out of this 

range shuts down the system and displays "Shutdown by EMS" .

EMS 4mA SETPOINT

140 F

[

 

]

EMS 20mA SETPOINT

200 F

[

 

]

- EMS INPUT MODE -

 

Setback

 EMS Control

STAGe INTeRFACe

Normal, MODBuS-Monitor Only, MODBuS-Full Control 

Default: Normal

Stage Modbus from 0 to 247 

Default: 0

PReSS TO SeleCT:

 /<System Startup>/.../Stage Interface/ Stage A Modbus Add/ ...

•   These options are designed for Modbus operating burners equipped 

with the Siemens LMV controller .  If the burner did not have Modbus 

communication, then select Normal .

•   The MODBUS-Monitor Only option receives the alarm lockout status 

through the Siemens LMV Interface .

•   The MODBUS-Full Control option sends the modulation percent and 

receives the lockout status through the Siemens LMV Interface .

•   Order the LMV Interface for each of the MODBUS burners 

(HT# 926621-00) .  In addition, order the Interface Power Supply 

(HT #926622-00) for every 10 burners .  See LMV-Interface Manual .

•   When any of the Modbus options is selected from the Stage Interface 

menu, the Stage Modbus Address will follow .

•   Each Stage address must be unique on the Modbus network .
•   To exit the Stage Modbus Address, enter an address of 0 for the stage 

following the last stage .

STAGE A MODBUS ADD

1

[

 

]

STAGE B MODBUS ADD

0

[  

]

- STAGE INTERFACE -

 Normal

 MODBUS-Monitor Only
 MODBUS-Full Control

 AleRT

Regardless of the Modbus 

options selected, the 

Multi-MOD Platinum will also 

send a modulation signal to 

every active boiler through the 

Modulation Output terminals .

OuTPuT TYPe

135Ω, 0-10V, 0-5V, 2-10V, 1-5V, 4-20mA 

Default: 0-10V, 135Ω

PReSS TO SeleCT:

 /<System Startup>/ Sensor Type/.../Output Type A&B

•   The Multi-MOD Platinum has two Modulating Output Cards .  Each card 

modulates two stages .  Both stages must use the same modulating 

signal .  See "Modulating Output Card Installation" on page 23 .

•   Output Cards can be either 135Ω Cards for 135 ohm modulating motors 

or Current/Voltage Cards for current or voltage signal operating motors .

-OUTPUT TYPE A&B-

 Not Installed

 135ohm

 0-10v

 0-5v

 2-10v

 1-5v

 4-20ma

Содержание Multi-MOD Platinum





























































Отзывы:

Нет отзывов