manualshive.com logo in svg

heat-timer Mini-MOD, Инструкция по установке и эксплуатации

Поделиться
Скачать
heat-timer Mini-MOD Скачать руководство пользователя страница 10

10 

Heat-Timer Corp.

059040-00 C

Install tHe sensors

HeatIng systeM sensor (Hss) InstallatIon

HeatIng systeM sensor Hss

•   Put the Heating System sensor approximately 10' feet past the last boiler on the 

common supply header but before any major takeoffs.

•   The sensor must be located where it sees the output of all the boiler stages.  If a 

boiler is piped so that the sensor does not see its output, the Mini-MOD will not 

sequence the boilers correctly.

•   Only use a Standard Brass Tube sensor (HT #904220-00).

•   The sensor wires can be extended up to 500' using a shielded 2-conductor cable 

(Belden #8760 or equivalent).  Do not ground the shield at the sensor but at the 

panel using one of the terminals marked with an “O”.

•   Do not run sensor wires in conduit with line voltage wiring.

•   Install a 

⅜

" ID 1/2" NPT immersion well (HT #904011-00 or equivalent).

•   Insert the sensor probe of the supplied sensor into the well.

Immersion Well

3/8" ID 1/2" NPT

Heating System

Sensor

Common Supply Pipe

Sensor Probe

Immersion Heating System Sensor

Shield

Common Supply Pipe

Sensor Probe

Strap-On Heating System Sensor

Shield

Pipe Insulation

Connect

To control

 alert

If the HSS can not sense the correct 

heating system water temperature being 

supplied to the building, the Mini-MOD 

will not provide comfortable heat levels.  

Be sure the HSS is located on a main 

supply pipe which can not easily be 

isolated from the system.

outdoor sensor InstallatIon

•   Only use the Heat-Timer sensor included with the unit (HT# 904220-00).

•   Locate the sensor in the shade on the north side of the building.  The sensor 

should never be in direct sunlight.

•   Be sure the location is away from doors, windows, exhaust fans, vents, or other 

possible heat sources.

•   The sensor should be mounted approximately 10' feet above ground level.

•   Adhere the Outdoor Label provided to the back of the sensor base.

•   Use the Enclosure Base bottom knockout for the conduit.  Use the locknut to hold 

the conduit and enclosure base together.  Screw the cover to the base.

•   If screws are used to affix the enclosure to the wall, make sure to seal around the 

sensor and wall except from the bottom.

•   The sensor wires can be extended up to 500' using shielded 2-conductor cable  

(#18/2).  Do not ground the shield at the sensor but at the control using the 

terminal marked with an “O”.

•   Do not run sensor wires in conduit with line voltage wiring.

 WarnIng

the Mini-Mod is an operating control only.  all boilers must 

have all safety and limit controls required by code.  It is the 

responsibility of the installer to verify that all the safety and limits 

are working properly before the Mini-Mod is installed.

 alert

determining the proper location of the outdoor sensor is very important.  the Mini-Mod will base the heat on 

the outdoor temperature information it receives from this location.  If the sensor is in the sun, or covered with 

ice, its reading will be different from the actual outdoor temperature (od).

System Sensor

In Well

Shield

Not connected

Well Locknut

Sensor 

in Well

Well

Sensor 2-Conductor

Shielded Cable

System

Strap-On

Sensor

Shield

Not connected

Plastic 

Tie-Wraps

Around Pipe

Outdoor

Sensor

snap-in

location

Shield

not connected

Conduit

Outdoor Label 

on back of Sensor

Outdoor Sensor

Strap-On Sensor

Immersion Sensor

Mounting

screws

location

Seal around 

sensor and wall

Outdoor

drip-hole

Содержание Mini-MOD





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды