Heat-N-Glo RHW-44 Скачать руководство пользователя страница 3

The RHW-44 fireplace system has been tested and
listed in accordance with UL 127 and ULC S610
Standards, and has been listed by Underwriters
Laboratories Inc. for installation and operation in the
United States and Canada as described in these
Installation & Operating Instructions.

The model RHW-44 fireplace has been tested and
listed for use with the components listed below.  The
optional components may be purchased separately
and installed at a later date.  However, installation of

an outside air kit will require significant reconstruc-
tion, and should be installed at the time of the initial
fireplace installation.

Check with your Local Building Code Agency prior to
installing this fireplace to ensure compliance with local
Codes, including the need for Permits and follow up
inspections.  If any assistance is required during
installation, please contact your local dealer or the
Heat-N-Glo Technical Services Department,
20802 Kensington Blvd., Lakeville, MN 55044.

WARNING!

THIS HEAT-N-GLO FIREPLACE AND ITS COMPONENTS ARE DESIGNED TO BE

INSTALLED AND OPERATED AS A SYSTEM.  ANY ALTERATION TO OR

SUBSTITUTION FOR ITEMS IN THIS SYSTEM, UNLESS ALLOWED BY THESE

INSTALLATION INSTRUCTIONS, WILL VOID THE UNDERWRITERS LABORATORIES

LISTING AND MAY VOID THE PRODUCT WARRANTY.  IT MAY ALSO CREATE A

HAZARDOUS INSTALLATION.  READ THROUGH THESE INSTRUCTIONS

THOROUGHLY BEFORE STARTING YOUR INSTALLATION AND FOLLOW THEM

CAREFULLY THROUGHOUT YOUR PROJECT.

This Heat-N-Glo fireplace system consists of the following:

1.

Fireplace/Integral Grate

3.

Chimney System

2.

Chimney Termination Cap

4.

Hearth Extension

Optional components include:

1.

Glass Doors

2.

Outside Combustion Air System

3-00

3                                                                                      33147A

RHW-44 WOODBURNING FIREPLACE

A.  LISTINGS AND CODE APPROVALS

B.  DESCRIPTION OF THE FIREPLACE SYSTEM

NOTE:  Illustrations throughout these
instructions reflect “typical installations”
and are for design purposes only.  Actual
installation may vary slightly due to indi-
vidual design preferences.  However,
minimum and maximum clearances must
be maintained at all times.

The illustrations and diagrams used
throughout these installation instructions
are not drawn to scale.

Tools and Building Supplies Normally
Required

Tools:

Building Supplies:

Saw

Hearth Extension Material

Pliers

Wall-finishing Materials

Hammer

Framing Material

Phillips Screwdriver

Fireplace Surround

Tape Measure

Caulking Material

Plumb Line
Level
Electric Drill and Bits
Framing Square

Содержание RHW-44

























Отзывы: