Heat-N-Glo L-Corner-TRC-CE Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 40

Heat-N-Glo L-Corner-TRC-CE Скачать руководство пользователя страница 29

29

For Vertical Runs -

One ceiling firestop is

REQUIRED

at

the hole in each ceiling through which the flue passes.

To install firestops for vertical runs that pass through ceilings:

• Position a plumb bob directly over the center of the verti-

cal flue component.

• Mark the ceiling to establish the centerpoint of the flue.

• Drill a hole or drive a nail through this centerpoint.

• Check the floor above for any obstructions, such as wir-

ing or plumbing runs.

• Reposition the fireplace and flue system, if necessary, to

accommodate the ceiling joists and/or obstructions.

• Cut an 280mm x 280mm hole through the ceiling, using

the centerpoint previously marked.

• Frame the hole with framing lumber the same size as the

ceiling joists.

Figure 24. Ceiling Firestop (Ceiling Side)

If the area above the ceiling is

NOT

an attic, position and

secure the ceiling firestop on the ceiling side of the previously
cut and framed hole.

Figure 23. Hole & New Framing Members

If the area above the ceiling

IS

an attic, position and secure

the firestop on top of the previously framed hole.

NOTE: Keep insulation away from the flue pipe at least
26mm.

Figure 25. Attic Firestop

JOIST

CEILING FIRESTOP

CEILING

NAILS (4 REQUIRED)

CEILING

CEILING FIRESTOP

RAFTER

NAILS (4 REQUIRED)

CEILING

NEW
FRAMING
MEMBERS

EXISTING CEILING
JOISTS

CHIMNEY
HOLE

280 mm

280mm

NOTE: There must be NO INSULATION or other
combustibles inside the framed firestop opening.

«
...
27
28
29
30
31
...
»

Содержание L-Corner-TRC-CE









































Отзывы:

Нет отзывов