27
!
WARNING: A 9.5 MM BEAD OF STOVE CE-
MENT MUST BE PLACED AROUND THE 127
MM FIREPLACE STARTING COLLAR BEFORE AT-
TACHING THE FIRST FLUE COMPONENT. FAILURE
TO SEAL THIS JOINT MAY CAUSE THE FIREPLACE
TO OPERATE IMPROPERLY. SEE THE DIAGRAM .
STARTING
COLLAR
STOVE
SEALANT
BEAD
1 INCH
(25.4mm)
FIRST VENT
COMPONENT
!
WARNING: ENSURE THAT THE FIBER-
GLASS ROPE GASKET SUPPLIED WITH
THE FIREPLACE SEALS BETWEEN THE FIRST
FLUE COMPONENT AND THE OUTER FIREPLACE
WRAP.
If the installation is for a termination cap attached directly
to the fireplace, skip to the sections,
Install Firestops
and
Flue Termination
.
1. Attach the First Flue Component to the
Starting Collars
To attach the first flue component to the starting collars of
the fireplace:
• Apply a 9.5mm bead of stove cement around the 127mm
fireplace starting collar.
• Make sure that the fireplace rope gasket supplied with
the fireplace seals between the first 219mm flue compo-
nent and the outer fireplace wrap.
• Lock the flue components into place by sliding the con-
centric pipe sections with four (4) equally spaced interior
beads into the fireplace collar or previously installed com-
ponent end with four (4) equally spaced indented sections.
• When the internal beads of each 219mm outer pipe line
up, rotate the pipe section clockwise about one-quarter
(1/4) turn. The flue pipe is now locked together.
Figure 18. Attaching the First Flue Component
to the Starting Collars
!
B. Installing Flue Components
After determining which set of starting collars will be used
(top or rear), follow flueing instructions accordingly.
Flueing Out the Rear Flue
Remove the installed rear seal cap from the rear starting
collars by removing screws (see Figure 17). Follow the flue
configuration tables accordingly.
Remove the insulation from the
REAR
five inch flue, pull
the heat shield out from outside of the firebox.
WARNING: THE TOP HEAT SHIELD (INSIDE
THE FIREBOX) MUST REMAIN ATTACHED IF
THE FLUE SYSTEM IS ATTACHED TO THE
REAR STARTING COLLARS. SEE FIGURE 17.
Flueing Out the Top Flue
Remove the screws in the top flue collar seal cap and re-
move the top flue collar seal cap and insulation inside the
top starting collar (See Figure 17).
Remove the heat shield from inside the
TOP
127mm flue
from outside of the firebox.
The glass must be taken off again for positioning the logs
when the unit is finally installed in place and finished around
it. Re-install the glass door. Attach flue system to the top
starting collars.
WARNING: THE REAR FLUE COLLAR SEAL
CAP MUST REMAIN ATTACHED TO THE REAR
FLUE COLLARS IF THE FLUE SYSTEM IS AT-
TACHED TO THE TOP STARTING COLLARS.
WARNING: FAILURE TO REMOVE INSULA-
TION IN THE SET OF COLLARS YOU ARE US-
ING COULD CAUSE A FIRE.
WARNING: YOU MUST LEAVE THE INSULATION
IN PLACE IN THE SET OF COLLARS YOU ARE
NOT USING.
If your vertical flueing component is over 3.1m, you may
want to install the vertical baffle (located in the bag containing
the install manual) to improve flame appearance. Center
the vertical baffle on the 127mm flue being used, and with
self tapping screws secure the baffle to the inside of the
firebox.
Figure 17
Flueing Out Rear
Flueing Out Top
!
!
!
HEAT
SHIELD
DISCARD
INSULATION
and
HEAT SHIELD
HEAT
SHIELD
DISCARD
and
HEAT SHIELD
INSULATION
SEAL
CAP
SEAL
CAP
