Heat-N-Glo 8000TVC Скачать руководство пользователя страница 10

7

Step 4

Installing the

Vent System

A.  Vent System Approvals

Model 8000TVC is approved to use 6-inch (152mm)

diameter B-type vent. B-type vent must be used

when the vent system is within combustible

construction.
These models may also use single wall rigid or flexible

gas vent 

IF 

and 

ONLY IF

 the vent system is installed

within non-combustible construction such as a masonry

chimney.  The same diameter noted above for B-type

vent must be used for single-wall vent.  See Figure 5.
For B-type vent the clearance to combustibles is

1-inch. Follow vent manufacturers 

REQUIRED

clearances.
The flame and ember appearance may vary

based on the type of fuel burned and the venting

configuration used.

B.  System Components.

Vent System Configuration

RISE TO RUN RATIO = 2:1
MAXIMUM 

TOTAL HORIZONTAL RUN = 15 FT.

MINIMUM 

TOTAL VERTICAL RISE = 9 FT.

MAXIMUM NO. Of ELBOWS:

2 - 90

o

 or 4 - 45

o

Plan and install the vent system using the parameters

shown above.

WARNING: YOU MUST NOT EXCEED

THESE PARAMETERS.

Connect a B-Type vent component to the flue outlet collar.

Look at the vent pipe through the holes in the 10 5/8”

ring to check that the vent pipe is attached.

NOTE: It is always better to first attach a straight

section of vent to the unit before attaching an elbow.

Avoid  using elbows in the vent system if possible.

A 90-degree elbow can be attached directly to the unit.

If it is, it can be followed by a 

MAXIMUM 

15-feet

horizontal run, a second 90-degree elbow ending in a

minimum 30 foot vertical.
A minimum of 9 foot vertical rise ending in a listed

termination cap is required for the unit.
Continue to add vent components, until the vent run is

completed.

WARNING: YOU MUST NOT EXCEED A

TOTAL MAXIMUM HORIZONTAL RUN

OF 15 FEET FOR THE ENTIRE VENT

SYSTEM.

Содержание 8000TVC


























Отзывы: