Heat Controller A-VMH18DC-1 Service Скачать руководство пользователя страница 38

Страница: 38 / 50

Service Manual

VMH SerieS

Heat Controller, Inc.

9.3.2.6 High pressure protection (ODU P1) (Only for A-VMH36QC-1)

Replace outdoor main board

Evacuate the refrigerant, then use

high pressure nitrogen or refrigerant

to blow pipe, vacuum and recharge

with refrigerant again

Clean the heat exchanger

Remove all obstructions for proper ventilation

Stop the unit

Replace high pressure protector

Reconnect it properly

High pressure protection

Is the wiring between

the high pressure switch

and main control board is

connected correctly?

Yes

Is the high pressure

protector broken?

Short circuit the high

pressure protector socket,

check whether the system

can run normally now?

Yes

Check whether

the refrigerant

system is ok

Check whether the

outdoor ambient

temperature is higher than

109.4°F (43°C)?

Check whether the outdoor

unit’s airflow is obstructed

Check whether the heat

exchanger is dirty

Check whether the

refrigerant circuit has a

blockage

Yes

Содержание A-VMH18DC-1 Service



















































Результаты поиска

Содержание A-VMH18DC-1 Service

Отзывы:

Похожие инструкции для A-VMH18DC-1 Service

Бренды по названию

Популярные бренды

Heat Controller A-VMH18DC-1 Service, Руководство по обслуживанию

Результаты поиска

Содержание A-VMH18DC-1 Service

Отзывы:

Похожие инструкции для A-VMH18DC-1 Service

Бренды по названию

Популярные бренды